Re: Strange aerial configuration - Winegard.jpg (0/1)

Er, yes what I meant to say was it's an monodirectional, but mounted
on a swivelling base, anyway you get the drift. It's about 8 years old
and I am told that is about the time when the ampflifier goes 'puf'

There is a power supply to it, but only one downlead. The real thing
can be seen here: http://www.winegard.com/mobile/sensar.htm. This
looks the same but may have new characteristics in the more modern
model.

The question is, will a flat dipole like this work with UK / European
transmissions as well as the more usual designs ones I see in this
country?

Where would I buy a suitable amplifier for one?

Many thanks for the help, and yes, I have already been suitably
chastised by my ISP, and called an Abuser!

On Wed, 16 Apr 2008 11:23:29 +0100, "Bill Wright"
<insertmybusinessname@xxxxxxx> wrote:


"theman" <theman@xxxxxxxxxxxxxxx> wrote in message
news:kgeb0418trrrrgbumv6govh3q0e4bb3p7c@xxxxxxxxxx
Hi All,
I've bought an American motorhome and the aerial is decidedly odd
looking. It is omnidirectional, manually rotated and with a masthead
amp included. The question is, will this work in UK and Europe for
digital pictures?

My reason for asking is that it is currently faulty and I'm wondering
if it is worthwhile fixing. The other thing which occurred to me was
to replace the flat plates with two bits of UK aerial to see if that
helps.

I've attached a picture for which I apologize, but trying to describe
it in words would take up more bandwidth than the size of the picture!

The picture needs to be posted on a file sharing site or somewhere before we
can see it.

Your aerial isn't omnidirectional (you can rotate it). Most of these things
are a combined VHF/UHF, generally with two downleads. Some of them have
vertical elements as well as horizontal. Some of them have a third cable for
FM radio. For UK use it is unneccessarily cumbersome, although a replacement
might not look as nice!

The only thing that goes wrong with these is the built in amplifier. Are you
powering it correctly? There's often a power unit in a cupboard with LEDs on
it. Others take 12V to the amp directly (not thro the coax), in which case
there'll be a switch with a LED somewhere.

It isn't impossible to change the amp for a UK one. Use a low gain one.
Power via coax and use a line power injector to add 12V to the coax. Use a
500mA inline fuse.

If you lift the aerial off the van be careful with the seal. If it's
perished you have a problem.

Bill

.

Relevant Pages

  • Re: Strange aerial configuration - Winegard.jpg (0/1)
    ... I've attached a picture for which I apologize, ... Others take 12V to the amp directly, ... Power via coax and use a line power injector to add 12V to the coax. ...
    (uk.tech.digital-tv)
  • Re: Strange aerial configuration - Winegard.jpg (0/1)
    ... I've attached a picture for which I apologize, ... Others take 12V to the amp directly, ... Power via coax and use a line power injector to add 12V to the coax. ...
    (uk.tech.digital-tv)
  • Re: TV picture quality problems
    ... You might try a mast mounted amp. ... run power up there, you need a coax powered unit. ... far as I know there are no real requirements for an ATSC amp, ... requirement you could send the DC through the coax. ...
    (sci.electronics.repair)
  • Re: Design of SE amplifier output stages.
    ... Decide how much power your speaker needs. ... to go wrong with when trioded in something simple like an SE amp. ... Decide on transformer core material. ... Within this signal you'd want to have no more than 7Vrms of any signals ...
    (rec.audio.tubes)
  • Re: why it isnt so important, but still has meaning (long!).
    ... > amp, it may in some cases lead to problems, of which some are outlined ... > Let's assume an amplifier stage with BJTs in class AB such as we find ... > Good, negative loop feedback linearizes the amplifier's properties, so ... > Then we have the physical limitations of the power supply. ...
    (rec.audio.opinion)