Re: Jet cabinet saw, measuring tape

I know you think that may be a lousy way to sell a tablesaw but in this
case, it works for you.

First of all (and I have first-hand experience with a Jet cabinet saw), Jet
outsources the fence, rails, extension table etc. So before making anything
permanent, look it over carefully - especially the fence. Note the block
that is welded to the rear of the fence (underneath) and connects to the
lock/slider mechanism. Be sure the welds are all good and that this block
is reasonably centered. On the slider - are all the adjustments hex screws
able to be turned? I had one that wasn't threaded, one that was
cross-threaded. I went through 3 fences from Jet before finally getting one
that was welded correctly. Jet knew they had a quality problem and were
working it but right then, the fix was to sort thru the pile,find a good one
and send it out.

The locking mechanism has a piece of Teflon (or whatever it is) and the glue
they used to use simply didn't hold these pads in place very long. Simply
clean the surfaces off and reapply using a poly glue like Gorilla glue and a
small clamp to hold it in place.

Mount the front rail and be sure to follow the instructions. Once that is
all done and you're happy with the alignment and that everything works -
then apply the tape. Move the fence to the blade - that's the zero reference
obviously. Center the cursor (more on the cursor below) and be sure you can
move it about 1/8" left and right. Now follow their instructions for
mounting the tape.

Cursor. The new cursors that I've seen on the Jets (last year) all came
with a wider cursor alignment mark. Mine has the thin line and is more
accurate to me. But if you find you don't like it, call them and they used
to send out the old version to anyone that asked. Ask for two - just in case
you break one. Grumble a bit, they send it free......;-)

Bob S.


<fdumont@xxxxxxxx> wrote in message
news:1126190991.703214.39610@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
> Just received my new Jet JTAS cabinet saw with the XACTA fence and I am
> little distressed that the guide rail doesn't have the measuring tape
> already installed. Instead someoone has put a roll of Starret stick on
> measuring tape in the box and I'm somehow supposed to align that as
> precisely as Jet does at the factory!
>
> Has this happened to anyone else? Help!
>


.

Relevant Pages

  • Re: adResyncAllValues-Parameter funktioniert bei SQL Server nicht!?!
    ... wie Microsoft Access (Jet) unter der Voraussetzung die Entwicklungs- ... des SQL Überbaus) profitieren von einem serverseitigen Cursor, ... Wobei der SQL Server insofern schon die Ausnahme ... die Serverseitigen machen immer mal den einen oder anderen Ärger. ...
    (microsoft.public.de.vb.datenbank)
  • Re: Nur ein Feld einer Abfrage ausgeben
    ... Hängt nämlich vom Cursor ab. ... Stimmt auch wieder. ... Bei Dynamic hilft auch kein Movelast, ... Jet, ...
    (microsoft.public.de.access)
  • Jet Headache
    ... I have a Jet Supersaw with a sliding fence. ... rail system and extension table. ... this upgrade was done by some drunk engineer. ...
    (rec.woodworking)
  • Re: Need help choosing a table saw
    ... Jet, Delta, and Powermatic saws. ... Some of the options I would prefer would be a Beisemyer style fence ... Get a good blade. ...
    (rec.woodworking)
  • RE: Autonumber field alway set to 0 using OLEDB? Using ODBC work
    ... had the server side cursor, the KB article might not suitable for this ... you can install the latest service pack of Jet 4.0. ...
    (microsoft.public.data.oledb)