Being Well Grounded is the Best Foundation for Every Radio Shack

Telamon,

Being Well Grounded is the Best Foundation for Every Radio Shack
http://groups.yahoo.com/group/Shortwave-SWL-Antenna/message/9152

The Third Wire in the AC Power Cord is by-design an "AC Power
Return Path" -not- and RF Signal Ground Path.

Current Three Wire 'design' is for the delivery of AC Power.
(H)(R)
=(G)=
All three Wires are usually just 1/16" Multi-Stranded Copper Wire.
- - - The Current AC Power Electrical Plug End design looks like :
|| |
O

A better Three Wire 'design' is for the delivery of AC Power
to RF Signal Processing Equipment would be :
(H)(R) 1/8" Multi-Stranded Copper Wire
[===] Flat 1/4" Wide by 1/16" Thick Copper Webbing for RF Ground
- - - The better RF Signal Ground Plug End would look like :
|| |
=== 1/2" Wide by 1/32" Thick

B U T ! - Until then a Second Ground Wire that is by-design an
RF Signal Ground is recommended for most if not all equipment
in the Radio Shack - IHMO

The use of a Flat Webbed Cable or Copper Strap from the Radio
Shack's Ground to the Receiver is by-design specifically to create
an RF Signal Ground Path for that piece of equipment.

Ideally there is an RF Ground Window leading into the Radio Shack
and Everything is "TIED" into it to Create :

The Common RF Ground Radio Shack.
= The Zero Potential Radio Shack.
= The Noise Free Radio Shack.

NOTE - The RF Ground Window is 'tied' to a good earthen Ground Rod
that is Bonded to the House's own AC Power System.

Rec.Radio.Shortwave - Seaches :
* Ground + Bond + Electrical
GBE => http://tinyurl.com/kaxdn
* Ground + Window + Electrical
GWE => http://tinyurl.com/kz77e
* Radio + Shack + Ground + Window
RSGW => http://tinyurl.com/huxsn

Google Seach for : Radio + Shack
+ Ground + Window + Bond + Electrical
RSGWBE => http://tinyurl.com/lmv6z

being well grounded is the best foundation
for every radio shack - iane ~ RHF
Shortwave Listener Antennas => http://tinyurl.com/ogvcf
http://groups.yahoo.com/group/Shortwave-SWL-Antenna/
SWL Antenna Group => http://tinyurl.com/ogvcf

.
.
.. .
.

.

Relevant Pages

  • Re: no more RCA plugs?
    ... get into soldering, just get a pre-made RCA cable at Radio Shack, chop ... The relatively long 8" gives you a few chances to get the wire stripped ... nicely before you go back to Radio Shack for more. ...
    (rec.audio.tech)
  • Re: Advice - Verizon Canceling SR Great Lakes Mid-Contract
    ... Our local Radio Shack outlet store is closing. ... My friend Dave has a nice Startac on Alltel and said his battery wouldn't ... batteries and 2 leather cases. ... wire in bulk, too. ...
    (alt.cellular.verizon)
  • Re: WH20 light question
    ... Do not jumper around it. ... You should be able to pick up a replacement at Radio Shack. ... My question is can I just jump a wire across there or will it mess ...
    (rec.games.pinball)
  • Re: Transmitter Diode ByPass
    ... But the local Radio Shack doesn't have it. ... where I can find 36 gauge wire? ... resistor body as you can to make a jumper to replace the diode. ...
    (rec.models.rc.air)
  • Re: Should I PID my Heat Exchanger?
    ... how did you bring power into the PID (a separate line ... I stole the power off the rotary power switch which is ... 16 gauge unstranded copper wire for the power to the controller and the ...
    (alt.coffee)
Loading