Re: Power supply

The voltage gain of darlingtons is less that unity as a emitter
follower. but not the current gain. The base current is like 20 ma.
and the collector is like 20 amps that's a gain of 100. A good
regulator like a LM723 can regulate that easy. If the gain ain't there
in the darlingtons you need a drive transistor.

I use a 0.1 ohm 50watt resistor series with the output, that gives me
an extra 2 volt drop that isn't across the transistor and keeps 40
watts from heating up the output. You still lose 40 watts. It just
goes up in the resistor. The 0.1 ohm 50 watt is only good for like 22
amps.

Put a fan on the heatsink. 170 watts will get hot all the time.
I put a computer power supply fan on my supply, the output stays alot
cooler.
Once the current drops the fan cools it really fast.

You have a high transformer voltage because it's a 50 amp supply and
you are running it at only 20 amps.

On Jul 15, 8:23 am, jimmi...@xxxxxxxxx wrote:
happen.

The output of the regulator will likely try to go to its full input voltage rail
(because of the high gain of the darlingtons).  The feedback loop in the
regulator will try to bring it back down to the set output voltage.  It probably
can't because the gain of the darlingtons is too high, and the output stays
banged against the input rail (22V).

I dont understand what you mean by this. The voltage gain of the
darlington transistors is less than unity in this case since they are
being used as emitter followers.

I am dropping 8.5 volts at 20 amps or 170 watts is being dissipated by
the transistors. This may not be a real problem. I know my commercial
power supply of similar size only provides about 18 volts to the
collector of the pass transistors and this  would result in about half
as much power being wasted. What voltage would you normally expect at
the the collector of the pass transistors. I have also thought that
maybe I dont have that much of a real problem since I doubt if the
power supply will ever be put under the same demands as it does
working into my load bank. Also I think I should add two more
transistors in paralell with the two I have. I think this would
distribute the heat better over my heat sink and have less localized
heating.

I dont think the size of my heatsink is a problem, it is probably
overkill. it is a 8in chimney type heat sink( i think that what you
call them) 8x8x10 inches finned inside and out. The transistor body is
mount on the outside  withe the wires going down the inside of the
chimney. The end of the chimney is designed to take a muffin fan.

Jimmie

.

Relevant Pages

  • Re: Interesting developments
    ... Cascode is supplied from +150V through 2.6 kohms collector load. ... So with this setup I went about testing some transistors in my parts box. ... I even tried a MOSFET, which was interesting: more voltage gain, somewhat ...
    (sci.electronics.design)
  • Re: Interesting developments
    ... CCS tail and resistive collector load; a PNP gain stage (with emitter ... So with this setup I went about testing some transistors in my parts box. ... I even tried a MOSFET, which was interesting: more voltage gain, somewhat ...
    (sci.electronics.design)
  • Re: Interesting developments
    ... CCS tail and resistive collector load; a PNP gain stage (with emitter ... So with this setup I went about testing some transistors in my parts box. ... I even tried a MOSFET, which was interesting: more voltage gain, somewhat ...
    (sci.electronics.design)
  • Re: Power supply
    ... Fred is absolutely correct in saying that the pass transistors in most linear ... the higher CE saturation voltage of a darlington has no ... and you substitute darlingtons in their place, some very bad things could ... SOA graph shows the safe combinations of collector current and collector-emitter ...
    (rec.radio.amateur.homebrew)
  • Re: Power supply
    ... and the collector is like 20 amps that's a gain of 100. ... Huh, I thought the 723 was a voltage regulator, not current. ... transistors is just going result in the 723 seeing a lighter load wich ...
    (rec.radio.amateur.homebrew)
Loading