Re: Question: Servo noise.

refer to "Servo & TX alterations, calculators, clonepacs, make an ESC or
winch, FAQ."

Add Missing Channels to Transmitters
Electronic Speed Controller using an old servo
Diodes - How to jump to delta/charge/Cycle TX.
FlyWire for Helicopter - Tony Van Roon
Focus III - fit elevon trim.
Futaba 9C - Spread*** for recording transmitter programming
Futaba Campac. Make your own Clonepac aprox. $10.
Futaba Clonepac.
Futaba - Gyro hidden programs
Futaba (FAQ) - switch numbers
Futaba Service menu enabler, 128Kbit UltraPAC for Futaba, etc.
Futaba - Service and/or Parts No Longer Available
Futaba Skysport from 4 to 5 Ch. and Interface for PC
GOSLOW: realistic flap and landing gear actuation- Brent's RC
Hitec Flash 4 add Retract Switch - 5th channel
Hitec Flash 4 - add Trainer buddy box facility.
Hitec Flash 4&5 - Double Memory
Flash 4 &5 Voltage Calibration
Hitec Flash 4&5 - Fast-charging Mod
Hitec Flash 4 X - convert to Flash 5 X
Hitec HFP-10 - Servo Tester_Programmer inc Transmitter Pulse Width Tester.
Hitec HAS-2MB R/C RX - Modify to 3ch etc - site down email Alam for details
Hitec 535 - amend from 5 to 8 ch.
Is your Servo going Bad?? [
http://www.torreypinesgulls.org/Servoarticle.htm good starting point ]
Linear Output conversion
Ranger 3 - Extend to 7 Channel.
Reverser: servo reversing for Y-cord operation Brent's RC
RMG Servos (Yacht winches)
Sailwinch Servo - Adjust number of turns from your TX ***
S148 as a gear box.Servo - How the circuit works
S148 Servo ... How to modify for 360 degree rotation
Servo mods to 180 and 360 degree operation.. Gang and Fit servos to yachts &
boats.
Servo basics and driver - Ahmet Onat
Servo Calculator - ensure servo is powerfull enough for the job
Servo Comparison Chart - extensive by Fatlion.com
Servo to power your model boat
Servo - Digital FAQs : Hitec answers***
Servo (Digital) Programmer FAQs
Servo - Center & End Point Adjustment FAQ
Servo - FAQs : Hitec answers.***
Servo - Stop the jitters.: Hitec answers.***
Servo - Troubleshooting problems : Hitec answers.***
Servo Wiring Diagrams
Tonegawa-Seiko
Water Proof A Servo

regards
Alan's Hobby, Model & RC Web Links
http://homepages.ihug.co.nz/~atong/
..................................................................



"Jeremy" <jeremyshawSP@xxxxxxxxxxxxx> wrote in message
news:yDHQe.40478$Hk.6523@xxxxxxxxxxx
> Ok...so I'm starting to go insane! I'm trying to build a 4 channel
trainer.
> I've got everything finished except for the rudder / front wheel servo.
> Something is wrong with the rudder portion. The servo, without anything
> hooked up to it works fine. It's nice and smooth and doesn't make any
noise.
> If I attach the control for the front wheel, it still works fine. But the
> second I try to put the rudder on it starts chattering away. Sometimes I
> can get it to be quiet when centered, but as soon as I give it any input
it
> starts making the noise. I've heard about it having to try to hard, or
> exceeding its maximum travel limits etc. I can't seem to figure it out.
> I've tried using all the different holes in the control arms at both ends
> and I still can't seem to get it right. Now I'm even trying different
> attachments at the servo, like a clip instead of just a Z-bend etc. It's
> driving me nuts! Help.
>
> Jeremy
>
>


.

Quantcast