Re: Grass growing though chicken wire covering bulbs, best way to deal with it?

Hettie® wrote:


John McGaw wrote:
Hettie® wrote:

I expanded my front flowering bed about two feet. I used my tiller, tilled through it once, then added compost and lots of old potting soil that had a lot of peat in it (was out of peat), and tilled again, also used the edger. Then I planted my spring bulbs, daffodils, tulips, crocus, muscari.

Now new grass is growing up through the chicken wire in the new area. I covered everything with that but the daffs, anemones, and muscari to keep the squirrels and chipmunks when they come out of hibernation from digging them up.

Am I just going to have to pull it up, little clump by clump? I was thinking after the bulbs have bloomed in spring, foliage died and been given a spring feeding to cover that part with heavy black plastic until the next spring if I can't get it under control. It's an area I have had to water constantly, so I think maybe the plastic wouldn't trap too much moisture that could rot the bulbs but am not sure about that.

Any better ideas? I'm mad at myself for not at least trying stripping off the sod first and tilling it all up instead, and it made for tough going combined with tree roots from my clump of birches nearby. It has been covered with an old wide board for a border for two years now until I could figure out what I want to do about a more pleasing, more permanent border and get around to doing it.

I would like to be able to remove the chicken wire at some point, but am afraid if I don't, the critters will just dig them up in a subsequent year. I read that bulbs will grow through the chicken wire and flower. I could cover it with a layer of topsoil, but that won't solve the grass problem. Right now, it's just on the surface secured with u-shaped landscape pins.


If it is regular "chicken" chicken wire you probably won't have to worry about taking it up -- it is so thin that, buried, it should rust away on its on in short order. When I tried to prevent digging creatures (including a very determined 100+ pound Lab) from getting to my bulbs I used welded reinforcing mesh with fairly tight openings. The shoots from the bulbs always did well enough finding their way through the openings. The mesh was under the bark chip mulch so that it could, with much trouble, be pulled up and then put back. Sometimes this material can be found as surplus in stainless steel and this should last virtually forever but even the regular steel will last for a decade or more.

As for the grass, if it were mine I would [cue the wails, moans, and gnashing of teeth] carefully spray it with a light dose of glyphosate herbicide while the bulbs are dormant. Since these materials are absorbed by foliage and break down rapidly the bulbs should suffer no damage.

At last, thank you. I felt like an idiot with the dumb question of the year, but it has kind of been a setback for me, 2 beds like that. I can rip up the wire and try to pull the grass when there is more to grab, or little by little like I do everything else and tack the wire down again. Let it go for now, winter is coming, and what little grass is there now shouldn't hurt tulips next spring (the other bulbs naturalize in it anyway). Then I will need some kind of barrier edging or it will creep right back in.

As a last resort I will try the spray while the bulbs are dormant. I don't like sprays and chemicals, but after a very bad year on all fronts, I must do something. And thanks for the concrete reinforcing wire suggestion. I suppose it doesn't cut with my tin snips like the chicken wire. What do you cut yours with? A torch?

I googled and found cardboard, landscape cloth (have both of those), could try that when the bulb foliage dies back and cover it with mulch, but it takes a whole year to kill grass and then some. This is the nice kind, too.


The best tool I've found for cutting regular concrete reinforcing grid is a set of heavy nippers -- the wire would just chip the blades on tinsnips and bolt cutters seem an extreme step. I have 12" nippers which do service cutting heavy wire and there are few tools better for pulling nails. One thing to keep in mind when selecting the wire, of course, is what you want to keep out -- a chipmunk can fit through a really small hole. Luckily I didn't have them to contend with where I was -- mostly just squirrels and my lab (moose frequented the yard but seemed to prefer eating my trees and bushes and digging just isn't their forte).

--
John McGaw
[Knoxville, TN, USA]
http://johnmcgaw.com
.

Relevant Pages

  • Re: Grass growing though chicken wire covering bulbs, best way to deal with it?
    ... tilled through it once, then added compost and lots of old potting soil that had a lot of peat in it, and tilled again, also used the edger. ... I was thinking after the bulbs have bloomed in spring, foliage died and been given a spring feeding to cover that part with heavy black plastic until the next spring if I can't get it under control. ... I would like to be able to remove the chicken wire at some point, but am afraid if I don't, the critters will just dig them up in a subsequent year. ... I could cover it with a layer of topsoil, but that won't solve the grass problem. ...
    (rec.gardens)
  • Re: Grass growing though chicken wire covering bulbs, best way to deal with it?
    ... I was thinking after the bulbs have bloomed in spring, foliage died and been given a spring feeding to cover that part with heavy black plastic until the next spring if I can't get it under control. ... I would like to be able to remove the chicken wire at some point, but am afraid if I don't, the critters will just dig them up in a subsequent year. ... I could cover it with a layer of topsoil, but that won't solve the grass problem. ...
    (rec.gardens)
  • Re: Bally Vector GI lighting too bright to look at
    ... measure hot to common at the socket, you don't measure AC to ground. ... through a board and right out to bulbs. ... TP4 on the rectifier board with respect to ground (braided wire inside ... Both lamp drivers are for the Controlled Lamps, ...
    (rec.games.pinball)
  • Re: Bally Vector GI lighting too bright to look at
    ... measure hot to common at the socket, you don't measure AC to ground. ... through a board and right out to bulbs. ... TP4 on the rectifier board with respect to ground (braided wire inside ...  Both lamp drivers are for the Controlled Lamps, ...
    (rec.games.pinball)
  • Re: Bally Vector GI lighting too bright to look at
    ... through a board and right out to bulbs. ... TP4 on the rectifier board with respect to ground (braided wire inside ... the transformer as Lloyd mentions, enters the board at the J5 ...
    (rec.games.pinball)
Loading