Re: Creature Lamp Matrix Problems

Column could be the LM339, order a few of those, they're cheap.

GRY

"garavaml" <garavamll@xxxxxxxxx> wrote in message
news:UFhpf.39923$tV6.26583@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
> OK -- I jumpered Q85 to ground for the row and all lites in the row lit
> up... Sooo, I guess its a bad TIP102 at Q85, rite?
>
> I did the same for the column at Q95 and no dice.... Nothing... Now what
> for the column?
>
> Where's a good place to pick up TIP 102s???
>
> Thanks,
> MIKE
> "pincredible" <mrjmross@xxxxxxxxx> wrote in message
> news:pTgpf.13060$Eu3.6954@xxxxxxxxxxx
>> Is the whole row or column out? Or is it just one light.
>> If it's one light, reflow the pins on the light board.
>> If it's a whole row, double check the tip102 transistor for that row or
>> column by jumper-ing from the tab on the transistor to the side-rail or
>> other ground.
>> if you can get the row to work, replace the transistor.
>> otherwise...?? follow Lloyds advice ;) (I'm sure he'll be replying any
>> sec)
>>
>> "garavaml" <garavamll@xxxxxxxxx> wrote in message
>> news:1hgpf.43875$D13.40823@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
>>> I'm shopping a Creature and have run into a lamp matrix problem... I've
>>> looked over Clay's site and have narrowed it down to a particular row
>>> (#6) and column (#6)... I've checked the transistors for each row &
>>> column and they come up OK...
>>>
>>> What next? Does anyone know a particular IC that runs this particular
>>> row (6) and column (6)?? What do I do next? I checked the pins out of
>>> the board and they are dead for that column... I didn't check the row
>>> yet, but will today.
>>>
>>> What do I do? Also, who carries the IC chips assuming that I will need
>>> them to fix this up.
>>>
>>> Lastly, unrelated.. don't laugh.. Anyone gotta complete knocker assembly
>>> for creature for me? Its totally missing.. Again, no jokes please! :)
>>>
>>> Thanks,
>>> MIKE
>>>
>>>
>>>
>>
>>
>
>


.

Relevant Pages

  • Re: Creature Lamp Matrix Problems
    ... reflow the pins on the light board. ... > If it's a whole row, double check the tip102 transistor for that row or ... >> I'm shopping a Creature and have run into a lamp matrix problem... ... >> MIKE ...
    (rec.games.pinball)
  • Re: Creature Lamp Matrix Problems
    ... reflow the pins on the light board. ... double check the tip102 transistor for that row or ... > I'm shopping a Creature and have run into a lamp matrix problem... ...
    (rec.games.pinball)
  • Re: Creature Lamp Matrix Problems
    ... reflow the pins on the light board. ... > If it's a whole row, double check the tip102 transistor for that row or ... >> I'm shopping a Creature and have run into a lamp matrix problem... ... >> MIKE ...
    (rec.games.pinball)
  • Re: Pinball Circus MN <--Fueys take on the party
    ... Seriously, it was great to meet you, and Mike from WI, same to you. ... polishing the glass to make the pins sparkle before the party. ... Lloyd could get back to work. ... After a few beers, food ...
    (rec.games.pinball)
  • Re: post-op update
    ... Oy, kate, your wrist injury was just so much worse than mine, and mine was ... Mike just shook his head and said, "Oh, my" when I told him ... A word to the wise - don't get to expecting the pins to come out at 8 weeks. ... bone reaching out to hug one another. ...
    (alt.support.arthritis)