Re: Hotsy Pressure washer questions

Can't answer your orifice question either (I saw a girl standing on a corner that might...)
Beware the pressure side-an old machine may be weak and have corrosion or fatigue damage...don't want to hot-wash your face...
A fuel oil burner has a VERY narrow A/F range, and atomization, turbulence, temperature of the combustion chamber, and the character of the blower air flow all affect combustion. Make sure the blower wheel and passages are clean, run fresh diesel through it, and tweak the mix in tiny increments. You can pick up an HF laser temp guage(should have one anyway...) for $50. Good for getting the hottest flame.
JR
Dweller in the cellar

Gunner wrote:
One of the things I brought home this weekend..was a Mod 530 Hotsy
pressure washer. It had not been run in at least 5 yrs..so they
declared it surplus and loaded it into my trailer with a fork lift.

I had to replace the fuel lines (diesel/fuel oil burner) and putz with
the pressure switches, grease the pump etc etc etc. One wheel was a
cripple, so used the pair I got at the last show in Visalia (perfect
size..$5 for the pair)

Works pretty good. However...I think its running too rich. Now this
may be due to a worn orfice, or the fuel/air mixture is not right. Air
mixture apparently is changed by opening/closing a vented band that
goes around the air intake side of the motor/blower housing. If I open
it too much..I get white smoke and not much heat. If I close it too
much..I get a faint black smoke and not a lot of heat.

There is no online manual on the Hotsy website. Anyone know of the
proper way to set fuel air mixture on a #2 fuel oil blower/igniter
gizmo? Or what I should be looking for as far as the exhaust output
is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
drill bit that small anymore) I think...think there is too much fuel
going out the nozzle as the water tubes in the boiler are now pretty
blackened with soot (after filling the tank with a 5 gallon can here
marked Diesel..but had way way too much oil in it...had to dump it and
go buy some fresh..which did cause it to burn ..the first stuff
wouldnt even catch fire..and covered the tubes with oil..which smoked
a bit as it burned off.

Anyone know what the orfice size should be? I can solder it
shut..then redrill maybe.

I figure this is about the same sort of burner as a residential oil
burner..so...

Thanks

Gunner, now able to clean nasty oily machine tools squeeky clean



"A prudent man foresees the difficulties ahead and prepares for them;
the simpleton goes blindly on and suffers the consequences." - Proverbs 22:3


--
--------------------------------------------------------------
Home Page: http://www.seanet.com/~jasonrnorth
If you're not the lead dog, the view never changes
Doubt yourself, and the real world will eat you alive
The world doesn't revolve around you, it revolves around me
No skeletons in the closet; just decomposing corpses
--------------------------------------------------------------
Dependence is Vulnerability:
--------------------------------------------------------------
"Open the Pod Bay Doors please, Hal"
"I'm sorry, Dave, I'm afraid I can't do that.."
.

Relevant Pages

  • Re: Why does one need to LEAN OUT a CARB when climbing?
    ... It diverts low pressure air from the back of the venturi into the ... fuel drawn in is proportional to the air pressure. ...
    (rec.aviation.piloting)
  • Re: NEWS FLASH
    ... were to truly shake the nation to it's knees, ... Let them ride the oil tit and dance to Saudi tunes. ... Air Force Link - ... B-1B achieves first supersonic flight using synthetic fuel ...
    (alt.guitar.amps)
  • Re: Why does one need to LEAN OUT a CARB when climbing?
    ... Ultimately your engine depends on the mass flow of air divided by the mass ... But the amount of fuel drawn up is a function of the pressure ... However mass flow is the density * the size of the pipe * the velocity. ...
    (rec.aviation.piloting)
  • Re: Husky 500 XC
    ... I>> know that I need 500cc of oil. ... best results just adding the proper amount of oil, and leaving the air ... pressure at "equalized" with the forks extended. ... My first bike was a new 175 Penton. ...
    (rec.motorcycles.dirt)
  • Re: Turbocharging and Intercooling
    ... Dunno about diesel SAAB's but the IC on petrol ones is a front mount ... with boost and air flow for up to 300bhp. ... pressure drop, this results in an increase in WOT manifold pressure of ... fuel up to the programmed fuel cut point - at which point it cuts the ...
    (uk.rec.cars.modifications)