Re: Increasing Electricity into your home question


"sparty" <longoja@xxxxxxxxx> wrote in message
news:1139532111.190142.301710@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
I have a 150amp panel in my home, which is decently full, but probably
has space for about another 70amps worth of breakers, but only about 4
spots left.

I HAD planned on running a 70 amp breaker, and then 4 gauge wire to my
garage to a new breaker panel. That will probably max out my panel in
my house. I've done all of the math, and I'm pretty sure it can handle
that.

One of the reasons I am doing this is to run some 230V tools in my
garage. Now recently, I may have come across the opportunity to get a
used cheap Millermatic 250 Welder, which is going to pull 44-45 amps vs
the original 20 amps, I was going to pull with a smaller Welder. This
welder all by itself would require a 60 or 70 amp breaker. So now, I
would like to run 100 amps to my garage instead.

Because of this, I'm thinking I need to increase my House Panel from
150amps to 200amps. What all is involved in this? Does the electrical
company usually do this for free?

Service upgrades don't cost anything here unless you go underground. The
utility doesn't always change the drop anyway. Electricians like to be paid,
however. The electrician has to do everything beyond the service drop from
the pole.

I know I will need to buy a bigger
main breaker, will there be anymore cost involved?

Unless your existing panel is UL rated for a 200 amp breaker you will be
buying a new panel, which will come with a breaker. You might as well get
the new panel, which will have more spaces.

Is 4 gauge NM-B still ok for 100 amps, or is it pushing it too much?
Pushing that much through it, does that present a fire risk, or is 4
still enough? That kind of distance should be a 2% or less drop, which
is ok, just curious about heat.



This will be through my Basement Ceiling Joists, then up a Garage
finished wall, then through the Garage Attic, then to a Breaker Panel.
Should be about 70-80 feet.

Thanks, James

I think you'll be fine with your 70 amp subpanel. Install it and take some
current readings before you change your whole service. You'll probably be
surprised how little you're drawing.


.

Relevant Pages

  • Re: Basic electrical panel question.
    ... The first thing to check is if there are two empty slots available for ... another double slot breaker. ... Then next is the total capacity of the panel, 125 amp total, so so far so ...
    (misc.consumers.house)
  • Re: "Federal Pacific" Breaker box
    ... I would suggest Square D QO type panel. ... My house had a 60 amp service that was changed out ... "Surge Breaker" surge suppresser, two spaces for the generator back feed ...
    (alt.home.repair)
  • Re: 220 to shop
    ... detached garage; there is no in ground rod. ... outlets to run the door opener and 2 15 amp receptacles. ... I happen to have a 20 slot panel with 100 A main ... breaker and numerous 15-20 A breakers that remain from a recent upgrade to ...
    (alt.home.repair)
  • Re: Slightly OT-Compressors
    ... your local electrical codes may vary - what I did was to run heavy wire to ... disconnect, so I replaced the breaker panel, added a 50 amp disconnect (2X50 ... out of hte master breaker - so my garage has the same power as the house. ...
    (rec.crafts.woodturning)
  • Re: And I bought myself a compressor...
    ... a new 200 amp service panel ... in my garage, one to run my compressor and another for a welder. ... I want to have an electrician friend come in and split the basement (the ... I replaced it with a nice shiny 200 amp model and ran a 60 amp circuit to a new sub panel in the garage. ...
    (alt.autos.toyota)
Loading