Re: At power on tube filaments light up more than normal for a sec

Ian Iveson wrote:
Ian wrote:

Actually, in a conductor electricity does not 'flow at the speed of light' the net flow of electrons in a conductor is barely a few meters per second.

Two different things, depending on what you think electricity is. Flow of electricity happens much faster than your surely quaint "net flow of electrons".


Of course, hence the ,pedant></pedant> tokens.

Speed of light is not a great help, either, considering light may be considered to flow at different speeds, and doesn't flow at all in a heater wire.


Personally I am uncomfortable with the term 'flow' applied to light.

Arny would have been better off just saying it's really fast, or near-as-dammit instantaneous, and leave light out of it altogether.


Indeed.

There is something in what he says, in that "thermal inertia" cannot alone explain flashing. For a one-part heater, electrical inertia would be necessary, such as a choke. Since it happens without a choke or other source of electrical delay, there must be two parts to the heater.


Quite possibly.

Cheers

Ian
Ian

"Ian Bell" <ruffrecords@xxxxxxxxx> wrote in message news:ghjhra$295$1@xxxxxxxxxxxxxxxxxxxxxxxx
Arny Krueger wrote:
"flipper" <flipper@xxxxxxxx> wrote in message
news:tv2qj41a6c2vdveo579pelmeq8290fptfm@xxxxxxx

Well, I found this explanation.

http://reviews.ebay.com/Why-Mullard-Amperex-12AX7-flash-when-1st-energized_W0QQugidZ10000000002972031

That jives with what my first guess was. That a small bit
of filament was 'bare' while the rest is sort of
heatsinked inside the cathode section so the 'bare' part
flashes as the rest warms up slower. That would make it
just an artifact of their particular construction
technique.
Seem questionable:

"The "flash" is perfectly normal and it's a trademark characteristic of Mullard / Amperex tubes. There are a couple other brands that have a similar flash but I'll discuss Mullard / Amperex tubes specifically since they are my store specialty."

IME the flash was very common in the Japanese equipment that Lafayette used to import, back in the day of. Now, the Japanese may have been building tubes using Mullard/Amperex technology, but it was mostly the U.S. brand tubes that *didn't* flash.

"The flash occurs on one side of the filament wires between the bottom plate and the inside bottom of the tube and this phenomenon only occurs when powering up from a cold start. The sudden influx of current on the cold heater filament encounters very little resistance along this wire (hence the sudden burst of light). So in effect one side of the tube always warms up 1st, the second takes a while to catch up but before long the heat is evenly distributed (and your amp comes to life). "

Electricity flows at the speed of light,
<pedant>
</pedant>
Cheers

Ian


.

Relevant Pages

  • Re: Hum, Ground Loops and Safety
    ... If you have two reservoirs of water, ... the blockage between those two conductors, the electricity will flow from ... Imagine that you have a very, very sharp butcher's cleaver, and several ...
    (alt.guitar.bass)
  • Re: Wireless DC electricity?
    ... What if I want the flow of electricity to be only 1 electron wide? ... Any power supply that attempts to produce a voltage that is over the breakdown voltage of air has some major design problems. ... The voltage you cited is so extreme that, as you can see, it would require over 12 AU of separation between the positive and negative plates in order to prevent arc over. ... One limits current flow by having a large enough resistance across the power supply so as to limit the current flow from the supply. ...
    (sci.physics.research)
  • Re: At power on tube filaments light up more than normal for a sec
    ... Flow of electricity happens much faster than ... light may be considered to flow at different speeds, ... characteristic of Mullard / Amperex tubes. ...
    (rec.audio.tubes)
  • Re: At power on tube filaments light up more than normal for a sec
    ... "The "flash" is perfectly normal and it's a trademark characteristic of Mullard / Amperex tubes. ... in a conductor electricity does not 'flow at the speed of light' the net flow of electrons in a conductor is barely a few meters per second. ...
    (rec.audio.tubes)
  • Re: WiFi Locator
    ... afford a radio lived out where there was no electricity. ... FYI in the twenties "peanut" tubes along with ... The best antenna for the ... Lots of gain, 6 degrees vertical beamwidth, 90-120 degrees ...
    (alt.internet.wireless)
Loading