My First days with the Sound Devices 552 Mixer/Recorder

My First days with the Sound Devices 552 Mixer/Recorder

I got my 552 yesterday. First things first, let me say wow, as a first
impression it’s freakin’ awesome.

So, what is the 552? Well, take a 442 mixer, add an extra input
channel, then add a 2 channel recorder with time code input, then make
it way more configurable and easier to operate, add a bunch of
informative LEDs, add a weird sounding talking menu system and while
you’re at it, add a talk back circuit to boot… all in a package ½ lb
LESS than the 442… and voila – the 552.

Here is a list of the most noticeable differences between the 442 and
the new 552:

Front panel configurable

Remember all the switches on the left side of the 442? Well on the
552, they are gone. Instead, the options for mic/line levels and
phantom power are all accessible on the front panel via use of the
channels PFL(Pre-Fade Listen) switch in concert with the slate mic
switch to toggle settings.


The Knobs & Switches

The Input Faders are now contoured differently and sport a silver knob
on the tip of the fader for fingertip control. (I call it the “Suicide
Stick”, because it reminds me of the old steering assist knobs on
older style school buses from waaaay back in the day). I really like
the feel and response of the new faders.

The Coarse Gain, L/R Pot & Low-cut Filter knobs all have the same look
and feel, The only exception is that the Course gain has an additional
12db of upper end gain than the 442 had.

(22-72db on the 552 vs. 22-60db on the 442).

The Headphone Volume knob is now a digital knob with a built in
button. Not only does it control the headphones volume, but it also
controls MUCH more. When the Headphone knob is rotated, The VU meter
reflects the level of the volume.

The volume controller also controls secondary functions such as the
menu, LED brightness and return level control, depending on the button
or switch being held down, then using the volume control to adjust
setting and make selections with it’s push button. Simply pushing the
volume button engages the zoom function on the VU meter (which is a
mode where it shows you 0 to 20 on the mixer only, but spread over the
whole VU).

The PFLs operate differently from the 442. Rather than the “press and
hold” switches on the 442, when you slide the switch and let go of the
PFL, the channel is soloed until you slide it over again.

The Slate Mic/Tone switch is slightly changed too. When you quickly
slide the slate mic switch and release it, it solos the slate until
you slide it again. If you press and hold the slate switch for more
than a moment, it releases the slate mic when you release the switch.
The tone switch no longer latches. Instead, it acts like a press and
hold button, but when you hold it on for two seconds it stays in tone
mode until you flip the switch again to release it. The slate mic
level is adjusted by holding the slate mic and turning the headphone
volume knob. A visual level shows on the VU meter the volume change.
(This may SOUND complicated, but it’s very intuitive once you do it
for the first time!)

The Return switch for A & B returns now have LED lights showing if
they are active in the headphones. You can adjust the levels for the
headphones by holding the switch for the return on and adjusting the
headphone knob to raise or lower the levels. A visual level shows on
the VU meter the volume change.


Built-in Recorder

The 552 incorporates a high quality two channel WAV/MP3 Recorder. It
records in 16 or 24 bit and up to 96Khz WAV files.

It accepts incoming timecode, but does not generate it’s own. Timecode
needs to be fed into the mixer via a TA3 connector on the right side
to sync the device with a camera/s. This could be done a number of
ways, such as hardwiring, or the use of a lock-it box in the bag with
the 552, or even running a wireless transmitter on the camera sending
timecode out to a receiver in the bag to the 552.

The 552 automatically changes it’s timecode settings to reflect the
type of incoming timecode.

The file saving work flow saves each day of recording in a daily
folder (Year, Month,Day, 09Y10M15) and records filenames in order of
recording (Y,M,D, # – 09Y10M15-001.WAV). It also has a max recording
size of 2gb and automatically splits to the next file when it reaches
the limit.

Pressing and holding the Battery Check button enables SVEN to tell you
how much recording time remains on the card.

You have to remove the card and mount it in either a Windows or Mac
system to transfer the files. The USB connector that is next to the
card is for factory use only and does not allow you to use it to
transfer data.

Another nice feature of the recorder is the ability to playback files
to headphone AND/OR to your source mix or IFB. To enable Output/IFB
playback, hold down the Battery Button and press the play button.

There is a small chance of bumping the record toggle button, but I
don’t think it’s that much of a problem, but a record switch lock
might be a nice future addition.


The Menu

Getting into the control menu is much easier and can be done without
having to turn on and off the device. In fact, it can be operated
while actively mixing without interrupting the program! To access the
menu, hold down the Battery Check Button and click the Headphone
button. SVEN guides you through the setup of each function. He takes a
little getting used too. Use the volume control to guide yourself
through the menu items and use the volume push button to choose your
selection. To exit the menu and accept your changes, simply push the
battery check button.

Menu items are quite diverse and there are many more configuration
options than with the 442.


Talkback Function

When the talkback function is selected in the menu, the 1/8” headphone
jack is split off (from the 1/4”)

so that the slate mic appears in the right monitor of the boom
operator’s headphones for discreet communication from to the mixer. In
this mode, the slate mic does not go to program mix. There are various
options for what gets routed to the boom op.

As of yet, I’m not sure if it can be configured to allow for a
talkback from the boom op.


New LEDs

There are a lot more LEDs on the 552 than the 442. Whereas the 442 had
Level , Headphone, Peak, Limiter and Power LEDs, the 552 has many more
informative LEDs than it’s predecessor. Each pot has it’s own channel
specific LEDs that show the status of the channels phantom power and
line/mic status. Some channels have other LEDs for Phase, MS, and
Channel Linking.

There is another LED directly above each pot that I particularly like:
the Input Signal LED. Where as the 442 had a Peak & Limiter LED, the
552 now has a single LED the changes colors and brightness depending
on the level pushing through the channel (green, yellow, red). It also
changes to an off-yellow when the PFL is activated on channel to show
that it is being soloed.

LED Brightness is controlled by holding the battery check button and
turning the headphones knob left (-) or right (+). There are MANY more
levels of brightness steps than the 442 five steps.

Other LEDs:

-The Record LED changes colors to reflect current recording/playing
status. It blinks yellow if no SD/SDHC card is in the slot or if the
card is in, but remains unformatted.

-The Zoom LED lights up when it is engaged.

-There is also a LED on the front that lets you know if timecode is
actively being fed to the 552.

-Just like the 442, the Headphones LED will glow read when the
headphone amp starts to overload.

Other noticeable differences:

-Supports AES Digital outputs.

-Return Loop back ability (Takes the A&B return and sums them and
outputs to Tape Out and Mono Mic out)

-Split ear Return Monitoring (Listen to A Summed Returned in left and
B Summed Return in your right ear)

-Left Tone Oscillator function (to check to make sure your left and
right channels are properly set on cameras)

-Time of Day Date/Clock


What’s Missing?

Not much really.

One thing missing from the 552 vs the 442 is the option for T power
mics. All you 416T users are going to have to upgrade or get a Phantom
to T power converter.

I also wish the 552 had a built-in time code generator. Maybe the 552T
is in the future? We can only hope!


In Conclusion:

I really love my 552. It is an huge step forward in field mixing.

May the 442 rest sweetly in heaven… and the X5 burn baby burn! Long
live the 552!

(I will say that I used to have a Wendt X5 and it served me well for
many years, even though I had many particular issues with it
(limiters, channel bleed, etc.) )

See this post with picture gallery on my blog at:
http://blog.chrisdurfy.com/?p=130

More information can be found on the Sound Devices website at:

http://sounddevices.com/products/552.htm
.

Relevant Pages

  • Re: Doing the pedal dance...hard?
    ... The problem is, since they ride the same ground, the 'boost' channel LED ... I suppose the only way to wire it is to wire it so that the boost channel ... when I switch to clean, that shuts off both leds. ...
    (alt.guitar)
  • Re: Need a little design help on my latest project
    ... voltage, and go with the constant current drives for them. ... that the LEDs would be pretty voltage sensitive. ... That will require switch mode conversion, ... small inductor and schottkey, a couple of caps, and three fets. ...
    (sci.electronics.design)
  • Re: Need a little design help on my latest project
    ... voltage, and go with the constant current drives for them.. ... that the LEDs would be pretty voltage sensitive. ... That will require switch mode conversion, ... small inductor and schottkey, a couple of caps, and three fets. ...
    (sci.electronics.design)
  • Re: Need a little design help on my latest project
    ... voltage, and go with the constant current drives for them. ... that the LEDs would be pretty voltage sensitive. ... That will require switch mode conversion, ... small inductor and schottkey, a couple of caps, and three fets. ...
    (sci.electronics.design)
  • Re: Need a little design help on my latest project
    ... that the LEDs would be pretty voltage sensitive. ... That will require switch mode conversion, ... small inductor and schottkey, a couple of caps, and three fets. ... resistor and, consequently, the "accuracy" to which it holds the current ...
    (sci.electronics.design)