fritz card unter etch schon installiert ?

Hallo,

wie kriege ich raus, ob die ISDN-Fritz-Card unter Debian etch schon installiert ist, d.h. ich nur noch die Faxsoftware installieren muss?

Hier eine Ausgabe von dmesg - ich hab einfach mal alles reingepackt.

Kann ich dann z.B. Hylafax oder CapiSuite installieren - es geht hier nur um den Faxempfang in unserer WG.

gruß

Sebastian


Bootdata ok (command line is root=/dev/hdb1 ro )
Linux version 2.6.18-6-amd64 (Debian 2.6.18.dfsg.1-22) (dannf@xxxxxxxxxx) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Jun 16 22:30:01 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bbfb0000 (usable)
BIOS-e820: 00000000bbfb0000 - 00000000bbfbe000 (ACPI data)
BIOS-e820: 00000000bbfbe000 - 00000000bbff0000 (ACPI NVS)
BIOS-e820: 00000000bbff0000 - 00000000bc000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
DMI present.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fb7d0
ACPI: RSDT (v001 102307 RSDT0946 0x20071023 MSFT 0x00000097) @ 0x00000000bbfb0000
ACPI: FADT (v002 102307 FACP0946 0x20071023 MSFT 0x00000097) @ 0x00000000bbfb0200
ACPI: MADT (v001 102307 APIC0946 0x20071023 MSFT 0x00000097) @ 0x00000000bbfb0390
ACPI: MCFG (v001 102307 OEMMCFG 0x20071023 MSFT 0x00000097) @ 0x00000000bbfb0400
ACPI: OEMB (v001 102307 OEMB0946 0x20071023 MSFT 0x00000097) @ 0x00000000bbfbe040
ACPI: HPET (v001 102307 OEMHPET0 0x20071023 MSFT 0x00000097) @ 0x00000000bbfb77c0
ACPI: NVHD (v001 102307 NVHDCP 0x20071023 MSFT 0x00000097) @ 0x00000000bbfbe0c0
ACPI: DSDT (v001 A0855 A0855000 0x00000000 INTL 0x20051117) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 0000000140000000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-0000000140000000
On node 0 totalpages: 1013204
DMA zone: 3052 pages, LIFO batch:0
DMA32 zone: 751592 pages, LIFO batch:31
Normal zone: 258560 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x508
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c0000000 (gap: bc000000:42c00000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists. Total pages: 1013204
Kernel command line: root=/dev/hdb1 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 25.000000 MHz WALL HPET GTOD HPET timer.
time.c: Detected 2100.480 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 4000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 3975988k/5242880k available (1928k kernel code, 152064k reserved, 867k data, 176k init)
Calibrating delay using timer specific routine.. 4205.85 BogoMIPS (lpj=8411703)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12502874
Detected 12.502 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4200.52 BogoMIPS (lpj=8401051)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Processor model unknown stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 530 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=299
checking if image is initramfs... it is
Freeing initrd memory: 4901k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:12.0
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *11
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0400
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0103
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0F03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 16 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:06' and the driver 'system'
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: match found with the PnP device '00:0c' and the driver 'system'
pnp: 00:0c: ioport range 0x230-0x23f has been reserved
pnp: 00:0c: ioport range 0x290-0x29f has been reserved
pnp: 00:0c: ioport range 0xa00-0xa0f has been reserved
pnp: 00:0c: ioport range 0xa10-0xa1f has been reserved
pnp: match found with the PnP device '00:0e' and the driver 'system'
pnp: match found with the PnP device '00:0f' and the driver 'system'
PCI: Bridge: 0000:00:08.0
IO window: d000-dfff
MEM window: dfe00000-dfefffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: e000-efff
MEM window: dff00000-dfffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0f.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:10.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:11.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Setting latency timer of device 0000:00:0f.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
PCI: Setting latency timer of device 0000:00:11.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1217460076.908:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[0562:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
PCI: Setting latency timer of device 0000:00:0f.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0f.0:pcie00]
PCI: Setting latency timer of device 0000:00:10.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:10.0:pcie00]
PCI: Setting latency timer of device 0000:00:11.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:11.0:pcie00]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0d' and the driver 'serial'
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
GSI 16 sharing vector 0xE9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 23 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 233, io mem 0xdfdff000
8139too Fast Ethernet driver 0.9.27
SCSI subsystem initialized
libata version 2.00 loaded.
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI Interrupt Link [UB11] enabled at IRQ 22
GSI 17 sharing vector 0x32 and IRQ 17
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [UB11] -> GSI 22 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 50, io mem 0xdfdfd000
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
GSI 18 sharing vector 0x3A and IRQ 18
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKB] -> GSI 19 (level, low) -> IRQ 58
eth0: RealTek RTL8139 at 0xffffc2000000a800, 00:08:54:54:fb:ff, IRQ 58
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
sata_nv 0000:00:09.0: version 2.0
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
GSI 19 sharing vector 0x42 and IRQ 19
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSA0] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0xC480 ctl 0xC402 bmdma 0xBC00 irq 66
ata2: SATA max UDMA/133 cmd 0xC080 ctl 0xC002 bmdma 0xBC08 irq 66
scsi0 : sata_nv
ata1: SATA link up <unknown> (SStatus E3229F03 SControl 0)
ata1.00: ATA-7, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 0)
Vendor: ATA Model: ST3160815AS Rev: 4.AA
Type: Direct-Access ANSI SCSI revision: 05
sata_sil24 0000:03:00.0: version 0.3
ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
GSI 20 sharing vector 0x4A and IRQ 20
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNEA] -> GSI 18 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:03:00.0 to 64
ata3: SATA max UDMA/100 cmd 0xFFFFC20000058000 ctl 0x0 bmdma 0x0 irq 74
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ata4: SATA max UDMA/100 cmd 0xFFFFC2000005A000 ctl 0x0 bmdma 0x0 irq 74
scsi2 : sata_sil24
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_sil24
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7, max UDMA/133, 976773168 sectors: LBA48 NCQ (depth 31/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/100
Vendor: ATA Model: MAXTOR STM350063 Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20
GSI 21 sharing vector 0x52 and IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 20 (level, low) -> IRQ 82
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 82, io mem 0xdfdfec00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 3:0:0:0: Attached scsi disk sdb
ACPI: PCI Interrupt Link [UB12] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [UB12] -> GSI 23 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 233, io mem 0xdfdfe800
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Probing IDE interface ide0...
hda: HL-DT-STDVD-ROM GDR8164B, ATAPI CD/DVD-ROM drive
hdb: Maxtor 4D040H2, ATA DISK drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 52X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
hdb: max request size: 128KiB
hdb: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63
hdb: cache flushes not supported
hdb: hdb1 hdb2 < hdb5 >
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Losing some ticks... checking if CPU frequency changed.
input: PC Speaker as /class/input/input1
CSLIP: code copyright 1989 Regents of the University of California
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:05' and the driver 'parport_pc'
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0
hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1
HiSax: Card 1 Protocol EDSS1 Id=fcpcipnp0 (0)
HiSax: DSS1 Rev. 2.32.2.3
HiSax: 2 channels added
HiSax: MAX_WAITING_CALLS added
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 17
GSI 22 sharing vector 0x5A and IRQ 22
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKA] -> GSI 17 (level, low) -> IRQ 90
hisax_fcpcipnp: found adapter Fritz!Card PCI v2 at 0000:01:06.0
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
ts: Compaq touchscreen protocol output
Adding 5839588k swap on /dev/hdb5. Priority:-1 extents:1 across:5839588k
EXT3 FS on hdb1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present


.

Loading