Re: Welches Modul f. Dawicontrol DC-2975U

Al Bogner wrote: 
Ja, wäre interessant, denn da werden die selben Chips verwendet.
DC-2976 UW      Symbios 53C875  NCR53C8xx oder Symbios875

Welche Distri verwendest du und hast du irgendwas speziell angepasst?

Fedora Core 4, out of the box. Keine Anpassungen. Wurde auch unter FC3 ohne Probleme eingesetzt.
Bei der ersten Durchsicht ist mir nur gerade folgendes Aufgefallen. Ich hab bei der Ausgabe von lspci bei "Control: BusMaster" ein +, bei dir ist es ein -.

>Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr-
>Stepping- SERR- FastB2B-

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-

Weiss der Geier :-) was das bedeuten mag.

Ich musste übrigens mehrere Steckplatzkombinationen ausprobieren, bis alles zusammen funktionierte (Hab noch eine Quad-Port NIC und einen Adaptec SATA Raid Controler drin).


Gruss,
Michael





[root@hydrogen ~]$ uname -a
Linux hydrogen.pse.local 2.6.12-1.1447_FC4 #1 Fri Aug 26 20:29:26 EDT 2005 i586 i586 i386 GNU/Linux



[root@hydrogen ~]$ lsmod |grep sym
sym53c8xx 82009 0
scsi_transport_spi 19777 1 sym53c8xx
scsi_mod 145161 5 st,sym53c8xx,scsi_transport_spi,aacraid,sd_mod


[root@hydrogen ~]$lspci -vvv
[..]
00:0a.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 26)
Subsystem: LSI Logic / Symbios Logic LSI53C876/E PCI to Dual Channel SCSI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 134 (4250ns min, 16000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at 9800 [size=256]
Region 1: Memory at d5800000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at d5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[..]


[root@hydrogen ~]$dmesg
[..]
sym0: <875> rev 0x26 at pci 0000:00:0a.0 irq 14
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi1 : sym-2.2.0
 target1:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 15)
  Vendor: QUANTUM   Model: DLT7000           Rev: 296D
  Type:   Sequential-Access                  ANSI SCSI revision: 02
 target1:0:3: Beginning Domain Validation
 target1:0:3: asynchronous.
WIDTH IS 1
 target1:0:3: wide asynchronous.
 target1:0:3: Domain Validation skipping write tests
 target1:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 15)
 target1:0:3: Ending Domain Validation
[..]

[root@hydrogen ~]$ lspci
00:00.0 Host bridge: ALi Corporation M1541 (rev 04)
00:01.0 PCI bridge: ALi Corporation M1541 PCI to AGP Controller (rev 04)
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:03.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] (rev c3)
00:09.0 PCI bridge: Intel Corporation 21152 PCI-to-PCI Bridge
00:0a.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 26)
00:0c.0 RAID bus controller: Adaptec AAC-RAID (rev 01)
00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c1)
01:00.0 VGA compatible controller: ATI Technologies Inc Rage XL AGP 2X (rev 27)
02:04.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
02:05.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
02:06.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
02:07.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 14)
[root@hydrogen ~]$

.

Relevant Pages

  • Reg. Ethernet Controller Access Problem
    ... Ethernet Boot Loader Configuration: ... F) Format flash ... Rajesh Going to detect and initialize Ethernet controller first time. ... Inside SendFrame ...
    (microsoft.public.windowsce.embedded)
  • Reg. Ethernet Controller Access Problem
    ... Ethernet Boot Loader Configuration: ... F) Format flash ... Rajesh Going to detect and initialize Ethernet controller first time. ... Inside SendFrame ...
    (microsoft.public.windowsce.platbuilder)
  • Problem: network drops; ethernet driver problem? (IRQ 11 disabled)
    ... Problem: The network drops out with message: "irq 11: nobody cared! ... much ethernet traffic is happening on the machine) the network drops ... ParErr+ Stepping- SERR+ FastB2B- ... 00:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev ...
    (Linux-Kernel)