Re: newbie & canonscan fs2710

"RizAmer" <yvesblochgolliot@xxxxxxxxxx> wrote in message
news:kvgae1dtk0s2mo474juho9msa2itdmp6dm@xxxxxxxxxx
> Thu, 21 Jul 2005 20:26:10 GMT, aut: "CSM1" <nomoremail@xxxxxxxxxx>
>
> >"RizAmer" <yvesblochgolliot@xxxxxxxxxx> wrote in message
> >news:8rtvd1pjpa7g6ou0u601duushiirl6oumm@xxxxxxxxxx
> >> Hi all! I am trying to use such device on my Windows98se system.
> >> I connected its PCI SCSI (Canon AVA-2904E) card: not detected (didnt
> >> appear in
> >> the i/o list)
> >> Changed for a 'SCSI PCI 8100S Symbios Logic 53C810', Windows provided
> >> driver.
> >> I installed CanoCraft v3.6.6 from Canon site.
> >> So far, so good, but (you know there is one) I keep getting an error
msg:
> >> 0x80210000 no scanner found
> >> I tried rotating the SCSI ID switch at the rear of ths FS2710, swapping
> >> the SCSI
> >> connector: no success.
> >> In the I/O list, there is a yellow question mark on a device named
Canon
> >> IX-27025E. Do I need another driver ?
> >> Any help ?
> >> La vitesse vous effraie ? Windows est fait pour vous.
> >
> >Disconnect the scanner.
> >
> >Remove the yellow question marked Device in Device Manager, reboot.
> >
>
> Done
>
> >You may need the correct Driver for the AVA-2904 card, Windows 98 may not
> >have the correct driver.
>
>http://www.adaptec.com/worldwide/support/driverdetail.jsp?sess=no&language=
English+US&cat=%2FOperating+System%2FMicrosoft+Windows+98&filekey=7800_fms30
3_disk1.exe
> >
> >If the above long link breaks:
> >Your shorter link is: http://makeashorterlink.com/?Z15C2697B
> >

Did you download and install the above driver?
You may have to remove the old (wrong) SCSI driver first.

> Not done, the ava-2904 is not detected, neither bios nor windows
> I changed to Symbios Logic 53C810 PCI card

The Adaptec AVA-2904 SCSI Card uses a Adaptec 7800 Family Chip it is NOT a
Symbios Logic 53C810.
You may have to get a different SCSI card with driver for Windows 98SE.

Windows 98 is supposed to have ASPI installed, if there is not a ASPI layer,
SCSI scanners are not detected by the OS but the SCSI card is seen.

To get a ASPI layer download from Adaptec.
http://www.adaptec.com/worldwide/support/drivers_by_product.jsp?sess=no&language=English+US&cat=%2FProduct%2FASPI-4.70&prodkey=Windows+ASPI+Package

Direct link to download:
http://download.adaptec.com/software_pc/aspi/aspi_471a2.exe


>
> >Disconnect the scanner.
> >Remove the current (wrong) scsi driver. (Remove in Device Manager) Reboot
> >computer. Install this download. Reboot.
> >
> >Set the SCSI ID switch on the scanner to 2 unless you have a SCSI device
2,
> >then choose another ID. ID 7 is reserved, do not use. ID 0 and ID 1 are
> >reserved for Hard Drives.
> >Do not change the ID after the scanner is recognized.
> >
> >You have installed the Scanner TWAIN driver haven't you.
> >It is best to get the latest driver.
> >
> >Support for the FS2710:
>
>http://consumer.usa.canon.com/ir/controller?act=SupportDetailAct&fcategoryi
d=235&modelid=8234
> >
> >After the TWAIN driver is installed, reboot once more.
>
> I downloaded CanoScan 3.6.4. Install went ok. Scanner is recognized.
> CanoScan application sees it, diags it ok
> BUT: whenever I request a preview or a scan (of a slide), the scanner is
> activated, I can see the slide move, the scan light but after a while,
operation
> always ends with the msg: (translated from french) "SCSI error, device not
> connected or power off, error 0x80210000". In addition, the "progress"
windows
> never change"

Does not seem the SCSI card is getting the correct command.

> By the way, how can I see (windows98se) if twain drivers are installed ?

Look in C:\Windows\Twain_32\ScannerName\ there will one or more files, one
will be a .ds.

Or with any TWAIN capable Photo editor, the File>Select Source will list the
TWAIN data source for all that are installed.

>
> >
> >Shut down the computer. Connect the SCSI cable, Check the termination ON
if
> >there is one. Power the scanner from a separate power from the computer,
> >turn scanner on. Start the computer.
> >
> >Windows 98 should now detect the scanner and install hardware.
> >
> >After the hardware is installed Open the TWAIN in a TWAIN compliant Photo
> >Editor. File>Select Source if one exits in the photo editor. Then
> >File>Import or File>Acquire.
> >
> >--
> >CSM1
> >http://www.carlmcmillan.com
>
> --
> "...et mon courroux, coucou !" (Desproges)
--
CSM1
http://www.carlmcmillan.com
--


.

Relevant Pages

  • Re: Printer fatal error during installation
    ... You meant you uninstalled your printer driver. ... Restart if necessary to get the hdw recognized by Vista. ... software,download and install the latest printer driver or software from ... The default printer setting may change after you install Windows Vista SP1 ...
    (microsoft.public.windows.vista.general)
  • Cant successfully load Windows!!
    ... I purchased an Alienware M51 7700 laptop in October. ... driver in order for the Windows install CD to see the drive. ...
    (microsoft.public.windowsxp.general)
  • Re: duplicate entries in device managers.
    ... > I suspect my problem might be a digital research scanner I ... > tried to install, but I really thought I removed everything ... with Windows XP? ... In case you're not familiar with System Restore, ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: Is any part of Ethernet circuitry tied to Open Firmware?
    ... an operating system (Windows) must be ... The Mac is, but we're talking about Windows here, dumbkopf! ... There is no driver for the DSL modem. ... during the ordinary OS X install process. ...
    (comp.sys.mac.system)
  • Re: Universal sound card?
    ... Decided to install within windows on a laptop. ... I don't really know the technicalities of an install to a file in a Windows ... translation layer which may eat up some of the memory seen by the kernel. ... Possibly there wasn't a driver for it in Ubuntu because the driver for your ...
    (comp.os.linux.hardware)