Re: Strange PEER error with Dani's 506 1.81 generic question

Well Bill ..

William L. Hartzell wrote:

Sir:

There is one other possibility and that is the local shared resources is/are not starting. I went onto that box just to find out and I discovered that I had disabled starting the local share when I switched over to using TCPbeui as it was the boot partition (I deleted the share and not seen the dialog in three boots today). SMB over TCP is TCPbeui, as in Netbios over TCP/IP. Firewalls only affects TCP/IP. If you are using NETbeui, aka Netbios, then the firewall is not part of the problem.

Turns out this issue with the new 1.8.1 version is more pervasive than I thought! I suddenly discovered that on ANY box of any kind on which it is installed, if there is no actual hard drive on the IDE cable, then the problem seems to be that no CD-ROM there is actually found during the boot up run.

Now on my R40 laptop, the hard disk and boot run completes. On it I don't know at this point if the CD-RW is found or not. As well, on an ASUS box with an AMD processor and IDE drive in a mobile drive tray, the IDE main drive for the box is found. However both the CD-ROM and a DVD in it are missing after the boot run!

The main box with the SCSI system an only the CD-ROM as the single IDE device on that cable has no CD-ROM after boot up .. leading to the share missing error during the requester startup. On another SCSI system with only a CD-ROM as the only device on that IDE interface on its Intel 915GAVL motherboard doesn't get found at all either.

At any rate, for the moment I'm back on Dani's 1.7.10 release of February of 2007 which is where all this was prior to the attempted latest release upgrade. Which works fine for all here for the moment.

I'd welcome other thoughts here from you or whomever. I really don't want to formally go towards Dani's realm until I can do so with only the right data and so on. Her time is far too valuable as to the contribution she has made to us all here with OS/2 to waste on information that really doesn't contribute to whatever is missing. I'd like to find someone else who sees this as well before focusing on what to present.

Thanks!

--


--> Sleep well; OS2's still awake! ;)

Mike Luther
.

Relevant Pages

  • Re: Cant install DVD-rom, system wont boot? Help???
    ... so the Primary IDE slots hold my 2 hard drives; ... Master and the second one is the slave to the master. ... want to leave it and change the slave cd-rom to a DVD-rom (not a dvd ... It won't boot into windows.. ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: Cant install DVD-rom, system wont boot? Help???
    ... so the Primary IDE slots hold my 2 hard drives; ... Master and the second one is the slave to the master. ... want to leave it and change the slave cd-rom to a DVD-rom (not a dvd ... It won't boot into windows.. ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: Strange PEER error with Danis 506 1.81 generic question
    ... reading this I would strongly recommend to send a trouble report to Dani. ... I went onto that box just to find out and I discovered that I had disabled starting the local share when I switched over to using TCPbeui as it was the boot partition. ... I suddenly discovered that on ANY box of any kind on which it is installed, if there is no actual hard drive on the IDE cable, then the problem seems to be that no CD-ROM there is actually found during the boot up run. ...
    (comp.os.os2.bugs)
  • Re: convert from scsi to IDE
    ... but I think you are missing something in what I wrote. ... >backup is finished shutdown and install the IDE drives. ... >boot your SCSI, which I presume also has the FreeBSD boot blocks ... So If I install IDE+SCSI, IDE will always win the boot. ...
    (freebsd-questions)
  • Re: PWS 500AU wont boot Tru64 CD
    ... Linux and OpenVMS installation CDs boot fine, ... Tru64 can only boot from the first CD-ROM on the first IDE ... Even with the boot device specified and working correctly, ...
    (comp.unix.tru64)