Re: Probleme with nm-16am v1.0

On 23 déc, 18:33, bod43 <Bo...@xxxxxxxxxxxxx> wrote:
On 23 Dec, 10:20, elias <liesbens...@xxxxxxxxx> wrote:

hello
i have a cisco 3725 router with ios ipbase 12.3(9e)
there are to nm-16am v1.0 card and a wic-1t connected
the router worked perfectly until electrical outage then the tow cards
nm-16am don't dialing or inswering
+ i can access the modems whith the telnet and i can't dialing or
inswering with AT commands it show me always NO CARRIER
can any one help me please
thank you

I don't follow what you are doing exactly however one
possibility to consider is that the configuration
was not saved and the reboot has lost the configuration
changes made since it was last saved.

sh start - displays the time the config was last saved *however*
this is the time as recorded by the router.

Some high end routers have battery backed clocks
(3725 may be one of them) however you have no way
of telling if perhaps the old config that might now be lost
was configured to use say NTP to get the time.

I think
sh calendar
will display the time from the battery backed clock.

If there is no calendar or if the calendar is not configured to
synchronise the clock the time starts from some particular
date - I forget which.

thank you for help but the statup-config was not deleted
here is my config (it's just a test config) :
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
modem country microcom_hdms europe
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
!
!
!
!
interface FastEthernet0/0
ip address 192.168.0.254 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
clockrate 2000000
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Group-Async1
ip unnumbered FastEthernet0/0
encapsulation ppp
async mode interactive
peer default ip address pool DIALIN
interface Group-Async1
ip unnumbered FastEthernet0/0
encapsulation ppp
async mode interactive
peer default ip address pool DIALIN
ppp authentication chap
group-range 65 80
!
ip classless
ip http server
!
!
line con 0
line 33 48
line 65 80
modem InOut
transport input all
autoselect ppp
line aux 0
line vty 0 4
!
end

the problem is that when i do i telnet 192.168.0.254 2065 to access
the modem 2/0 and perform an AT command to dial from the modem
ATDxxxxxxx
the modem do not dial
in a nother fact i do :
ATS0=1
to have a answering after 1 ring but the modem don't answer
thank you if you can help me
.

Relevant Pages

  • Re: lo0 for management
    ... have SNMP, AAA, syslog, etc configured) to use it, the router will use the ... IP address of the output interface as the source address of the packet. ... Configure the loopback to use a /32 mask. ... config for loopback0? ...
    (comp.dcom.sys.cisco)
  • Re: Cisco 1841 Router
    ... I have a Cisco 1841 Router ... unsure if I need the Multilink because there will be only one T1 ... You should use a multilink interface to "bond" several physical links. ... post your config when you get it close - we may be able to help ...
    (comp.dcom.sys.cisco)
  • Re: home lan setup suggestions
    ... Router internet config dialog shows: ... Default gateway: xxx.xxx.xxx.N+1, being the IP assigned by ISP ... Modem manages the connection/disconnection to internet, ... The router itself uses the gateway IP given to it by the ISP. ...
    (comp.security.firewalls)
  • Re: 20mbit/sec ADSL - will I need a new ADSL modem?
    ... I have a V2930 router configured with a V120. ... Wan1 = PPPoE ... The Draytek 120 modem is working fine, ... With PPPOE I found some bizzare config ...
    (uk.telecom.broadband)
  • Re: FreeBSD box/ADSL link config
    ... I have to configure PPPoE on the FreeBSD box? ... a web interface for configuration? ... The only thing you'll have to configure on the modem will be ... The DSL router in question is a Thomson Speedtouch 546v6. ...
    (freebsd-questions)