Re: please help ASAP 2611 issue

Sam wrote:
On Apr 28, 4:19 pm, "headsetadapter.com" <for-s...@xxxxxxxx> wrote:
Sam,

While you are in ROMMONITOR, do the command "dir bootflash:" or "dir flash:"
to see exact file name. Usually these files have a file extension ".bin".
You should provide FULL file name to successfully load router.

Good luck,

Mike
CCNP, CCDP, CCSP, CCVP, MCSE W2K, MCSE+I, Security+, etc.
CCIE R&S (in progress), CCIE Voice (in progress)
------
Headset Adapters for Cisco IP Phoneswww.ciscoheadsetadapter.comwww.headsetadapter.com

"Sam" <SamPa...@xxxxxxxxx> wrote in message

news:69f1a227-8845-430a-a836-25eeb239e854@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx



Hi everyone
I just loaded a new IOS on my 2611 and it will not boot. I keep
getting the message '
open: file "n" not found
open(): Open Error = -1
loadprog: error - on file open
boot: cannot load "flash:n"
and when i try to manually boot the flash this is the message I get. I
am completely out of ideas.
rommon 2 > boot flash:c2600-i-mz.122-12a
open: file "c2600-i-mz.122-12a" not found
open(): Open Error = -1c2600-i-mz.122-12a

loadprog: error - on file open
boot: cannot load "flash:c2600-i-mz.122-12a"
rommon 3 >
If anyone has any clue please tell me.
Thanks- Hide quoted text -
- Show quoted text -

I tried your dir bootflash: command and it gave me a bad device name
error. does that mean ios is corrupt?
Thanks for all your feedback

He also suggested "dir flash:".

Post the output of "dir flash:", and any "boot system" statements in the existing config.

You did backup a copy of the existing config before you commenced this process, didn't you?

Best Regards,
News Reader
.

Relevant Pages

  • Re: please help ASAP 2611 issue
    ... I just loaded a new IOS on my 2611 and it will not boot. ... and when i try to manually boot the flash this is the message I get. ... You did backup a copy of the existing config before you commenced this ... I did a dir flash: already and it is the only file that is up. ...
    (comp.dcom.sys.cisco)
  • Re: Cisco 6500 - how to change from router mode to hybrid (switch mode)
    ... The IOS that is on it does allow you to use it as as switch. ... I found that you actually need to format the flash on the SUP ... to accept the new OS so that it will boot properly. ...
    (comp.dcom.sys.cisco)
  • Re: WinCE 5.0 RegFlush on Cold Boot
    ... the highest risk when using flash is full corruption due to power ... I know that this is not what is happening and I'm sure this registry flush ... at boot would not wear out a flash block for years. ... constantly it would still last a decade before you had a failure. ...
    (microsoft.public.windowsce.platbuilder)
  • Re: WinCE 5.0 RegFlush on Cold Boot
    ... There's no clean way to prevent the flush, ... I know that this is not what is happening and I'm sure this registry flush ... at boot would not wear out a flash block for years. ...
    (microsoft.public.windowsce.platbuilder)
  • ASUS P4S800D: No joy...
    ... rebooted and installed LILO instead. ... And the disk DOES WORK. ... the floppy in, boot with the floppy, fix the config of LILO. ... Enable/Disable/Whatever various parameters, tinker with the config... ...
    (comp.os.linux.hardware)