Re: Port Aggregation NM-4E

Hello

from cisco docs the 3620 has pps from 20k-40k (look for routerperformance.pdf docs)


? 261x 1,500 0.768 15,000 7.68
262x 0.768 25,000 12.80
265x 2,000 1.024 37,000 18.94
3620 2,000 1.024 20,000 - 40,000 10 - 20


The fact is that I got an unused C3620 :)

I may replace the C3620 with a C2650 (with max mem 32F/128D) to install 12.4 ADVSEC
one integrated FE port and the NM1FETX

what should be the commands to do port aggregation, just to try?

thank you


"Thrill5" <nospam@xxxxxxxxxxxxx> ha scritto nel messaggio news:3oOdnQ3de-tp0nHanZ2dnUVZ_rGhnZ2d@xxxxxxxxxxxxxx
In theory, it could work, but I don't know for sure because I've never tried it, and never would -:) Something easy that will work is purchase another NM-1FE You can get one for less than $200. The 3620 is not a very beefy router and you won't get more than about 20MB/s of throughput. Another solution is to buy a 2621 or a 2611XM, both have dual FastEthernets and have about the same throughput (maybe more) as a 3620.

You need to verify that a 2912XL support LACP in order to avoid MAC flapping if you go the NM-4E route.

"Elia Spadoni" <admin@xxxxxxxxxxxxxxxxxxxx> wrote in message news:CMOdnZuN6f8JhnHanZ2dnUVZ8uGdnZ2d@xxxxxxxxxxxxxx
Hello
I have a C3620 (16F/64D) IOS 12.3(24) IP/FRW/IDS PLUS that is doing the firewall /nat device for my lan.

My network is this:

Edge Router C2650
"dmz switch" HP Procurve 2512

hp switch -> (DMZ/wan side) Eth1/0-----NM4E --{C3620} --NM-1FE-TX--- LAN C2950T-24

Can I bound all the four port of the NM-4E (or even just 2 or 3) to form a single port? The answer should be yes using the bridge group.

If I eventually replace the HP Switch with a Cisco Catalyst 2912XL, could I bound multiple ETH ports on the NM4E to aggregate bandwidth?
So I could transfer from the LAN (100mbit) to the DMZ side, at an higher speed?

Thank you







.

Relevant Pages

  • Re: Port Aggregation NM-4E
    ... from cisco docs the 3620 has pps from 20k-40k (look for ... one integrated FE port and the NM1FETX ... "dmz switch" HP Procurve 2512 ... So I could transfer from the LAN to the DMZ side, ...
    (comp.dcom.sys.cisco)
  • Re: pf and ftp from gateway
    ... # ephemeral port, so that the remote SIP proxy knows what session we belong ... pass in quick on $ext_if inet proto udp from any port bootps to ... pass out quick on $ext_if inet proto udp from $ext_if to any port bootps ... # allow lan requests from lan clients to exit EXT ...
    (comp.unix.bsd.openbsd.misc)
  • active ftp
    ... Does anyone have a pf config for active ftp? ... # Redirect lan client FTP requests ... # to the ftp-proxy running on the firewall host (via inetd on port 8021) ... rdr on $int_if inet proto tcp from $int_if:network to any port www -> ...
    (comp.unix.bsd.openbsd.misc)
  • Re: Remote desktop & Netgear router
    ... if you can connect to the PC from another PC using the "private LAN IP address" over your ... local LAN then Remote Desktop is obviously setup right and working. ... The issue then is the port forwarding on the router. ...
    (microsoft.public.windowsxp.work_remotely)
  • pftpx failing on freebsd 5.4-stable
    ... I'm trying to get ftp working from my lan to the internet. ... # when being port scanned. ... pass in quick on $ext_if inet proto udp from $isp_dhcp_server port bootps to ...
    (freebsd-net)