Re: Memory upgrade for PIX 515E
- From: Morph <notimportant@xxxxxxxx>
- Date: Mon, 19 Nov 2007 08:01:49 +0100
In the message
<10a23ff5-8247-4395-8432-a089897794ab@xxxxxxxxxxxxxxxxxxxxxxxxxxxx>
nakhmanson@xxxxxxxxx wrote:
| On Nov 15, 4:05 am, Morph <notimport...@xxxxxxxx> wrote:
| > In the message <1195077085.624943.256...@xxxxxxxxxxxxxxxxxxxxxxxxxxx>
| >
| > nakhman...@xxxxxxxxx wrote:
| >
| > | On Nov 12, 10:02 am, Morph <notimport...@xxxxxxxx> wrote:
| > | > Can a PIX 515E with the following configuration upgraded to 128 MB of
| > | > RAM?
| > | >
| > | > Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz
| > | > Flash E28F128J3 @ 0xfff00000, 16MB
| > | > BIOS Flash AM29F400B @ 0xfffd8000, 32KB
| > | >
| > | > Licensed features for this platform:
| > | > Maximum Physical Interfaces : 3
| > | > Maximum VLANs : 10
| > | > Inside Hosts : Unlimited
| > | > Failover : Disabled
| > | > VPN-DES : Enabled
| > | > VPN-3DES-AES : Enabled
| > | > Cut-through Proxy : Enabled
| > | > Guards : Enabled
| > | > URL Filtering : Enabled
| > | > Security Contexts : 0
| > | > GTP/GPRS : Disabled
| > | > VPN Peers : Unlimited
| > | >
| > | > This platform has a Restricted (R) license.
| > | >
| > | > Thank you for your time.
| > |
| > | Why not?
| > | here is output from one of my "pixes"
| > |
| > | pixfirewall# sh ver
| > |
| > | Cisco PIX Security Appliance Software Version 8.0(3)
| > |
| > | Compiled on Tue 06-Nov-07 19:50 by builders
| > | System image file is "flash:/pix803.bin"
| > | Config file at boot was "startup-config"
| > |
| > | pixfirewall up 36 secs
| > |
| > | Hardware: PIX-515, 256 MB RAM, CPU Pentium 200 MHz
| > | Flash i28F640J5 @ 0x300, 16MB
| > | BIOS Flash AT29C257 @ 0xfffd8000, 32KB
| > |
| > | 0: Ext: Ethernet0 : address is 0004.9ad0.d7cc, irq 11
| > | 1: Ext: Ethernet1 : address is 0004.9ad0.d7cd, irq 10
| > | 2: Ext: Ethernet2 : address is 0090.2775.c310, irq 9
| > |
| > | Licensed features for this platform:
| > | Maximum Physical Interfaces : 3
| > | Maximum VLANs : 10
| > | Inside Hosts : Unlimited
| > | Failover : Disabled
| > | VPN-DES : Enabled
| > | VPN-3DES-AES : Enabled
| > | Cut-through Proxy : Enabled
| > | Guards : Enabled
| > | URL Filtering : Enabled
| > | Security Contexts : 0
| > | GTP/GPRS : Disabled
| > | VPN Peers : Unlimited
| > |
| > | This platform has a Restricted (R) license.
| > |
| > |
| > |
| > | pixfirewall# sh mem
| > | Free memory: 154794120 bytes (58%)
| > | Used memory: 113641336 bytes (42%)
| > | ------------- ----------------
| > | Total memory: 268435456 bytes (100%)
| > | pixfirewall#
| > |
| > | thanks
| > | Roman Nakhmanson
| >
| > Thank you!
| > Did you just remove the installed memory and install a regular SD RAM
| > yourself? Because there is no option to order 256 MB memory through
| > cisco.
| >
| > Regards.
|
|
| >Did you just remove the installed memory and install a regular SD RAM yourself?
|
| yes
|
| > Because there is no option to order 256 MB memory through cisco
|
| of course not. 8-)
|
| PIX 515 (or 515E in your case ) is the (more or less) Intel pentium
| based PC. It supports up to 256M of RAM.
|
| Memory module has to have low density chips. In other words - you need
| two PC-133 non-ECC 8-chip 128MB modules
Thank you!
.
- References:
- Memory upgrade for PIX 515E
- From: Morph
- Re: Memory upgrade for PIX 515E
- From: nakhmanson
- Re: Memory upgrade for PIX 515E
- From: Morph
- Re: Memory upgrade for PIX 515E
- From: nakhmanson
- Memory upgrade for PIX 515E
- Prev by Date: Catalyst 3750 how to get multicast packets to go only to group member ports?
- Next by Date: dot1x authentication on windows xp and windows 2000 workstations
- Previous by thread: Re: Memory upgrade for PIX 515E
- Next by thread: Help in understanding an MPLS network (MPLS newbie)
- Index(es):
Relevant Pages
|
