Re: Terminal Server Setup
- From: MtbRoadie <smilin321@xxxxxxxxxxx>
- Date: 23 Apr 2007 13:52:17 -0700
Aaron,
I followed your directions but still can't connect. Here is the
results. The Serial 1/0 line is now down. I have it connected to a
Hyperterminal session with the settings 9600, 8 databits, No parity, 2
stopbits, Hardware flow control.
Chris
****************************************
* new config
****************************************
wbtermsrv1#show config
Using 2012 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname wbtermsrv1
!
boot system flash:c2600-is-mz.122-40a.bin
logging buffered 8192 debugging
enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
enable password
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
!
ip multicast-routing
call rsvp-sync
!
!
!
!
!
!
!
!
interface Loopback0
description GRE Tunnel Source Interface
ip address 10.144.0.80 255.255.255.255
!
interface Tunnel0
description GRE Tunnel Interface
ip address 10.144.2.26 255.255.255.252
ip accounting output-packets
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.144.254.1
!
interface Ethernet0/0
description LAN Interface
ip address 192.168.20.110 255.255.255.0 secondary
ip address 10.144.80.1 255.255.255.0
ip accounting output-packets
ip pim neighbor-filter 2
ip pim sparse-mode
ip route-cache flow
no ip route-cache cef
half-duplex
no cdp enable
!
interface Serial1/0
physical-layer async
no ip address
encapsulation slip
shutdown
async default routing
!
interface Serial1/1
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/2
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/3
no ip address
no ip mroute-cache
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.20.164
ip route 10.132.19.8 255.255.255.255 Tunnel0
ip http server
ip pim rp-address 10.132.19.8
ip pim spt-threshold infinity
ip mroute 10.132.19.8 255.255.255.255 Tunnel0
!
access-list 2 remark DISABLE DESIGNATED ROUTER
access-list 2 remark
access-list 2 deny any
access-list 111 remark used for debugging traffic
access-list 111 remark
access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
no cdp run
!
dial-peer cor custom
!
!
!
!
line con 0
exec-timeout 0 0
line 33
modem DTR-active
no exec
transport input telnet
line aux 0
line vty 0 4
password edocatad
login
!
end
wbtermsrv1#show config
Using 2012 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname wbtermsrv1
!
boot system flash:c2600-is-mz.122-40a.bin
logging buffered 8192 debugging
enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
enable password dci640
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
!
ip multicast-routing
call rsvp-sync
!
!
!
!
!
!
!
!
interface Loopback0
description GRE Tunnel Source Interface
ip address 10.144.0.80 255.255.255.255
!
interface Tunnel0
description GRE Tunnel Interface
ip address 10.144.2.26 255.255.255.252
ip accounting output-packets
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.144.254.1
!
interface Ethernet0/0
description LAN Interface
ip address 192.168.20.110 255.255.255.0 secondary
ip address 10.144.80.1 255.255.255.0
ip accounting output-packets
ip pim neighbor-filter 2
ip pim sparse-mode
ip route-cache flow
no ip route-cache cef
half-duplex
no cdp enable
!
interface Serial1/0
physical-layer async
no ip address
encapsulation slip
shutdown
async default routing
!
interface Serial1/1
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/2
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/3
no ip address
no ip mroute-cache
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.20.164
ip route 10.132.19.8 255.255.255.255 Tunnel0
ip http server
ip pim rp-address 10.132.19.8
ip pim spt-threshold infinity
ip mroute 10.132.19.8 255.255.255.255 Tunnel0
!
access-list 2 remark DISABLE DESIGNATED ROUTER
access-list 2 remark
access-list 2 deny any
access-list 111 remark used for debugging traffic
access-list 111 remark
access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
no cdp run
!
dial-peer cor custom
!
!
!
!
line con 0
exec-timeout 0 0
line 33
modem DTR-active
no exec
transport input telnet
line aux 0
line vty 0 4
password edocatad
login
!
end
************************************************
* new interface
************************************************
wbtermsrv1#show interface
Ethernet0/0 is up, line protocol is up
Hardware is AmdP2, address is 0003.e381.bbe0 (bia 0003.e381.bbe0)
Description: LAN Interface
Internet address is 10.144.80.1/24
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 11000 bits/sec, 12 packets/sec
5 minute output rate 9000 bits/sec, 10 packets/sec
6910660 packets input, 1028585734 bytes, 0 no buffer
Received 585985 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
6412939 packets output, 848479146 bytes, 0 underruns
6 output errors, 600 collisions, 1 interface resets
0 babbles, 0 late collision, 91614 deferred
6 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial1/0 is administratively down, line protocol is down
Hardware is CD2430 in async mode
MTU 1500 bytes, BW 9 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not set
DTR is pulsed for 5 seconds on reset
Last input never, output 3d08h, output hang never
Last clearing of "show interface" counters 3d02h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 6 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Serial1/1 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
27391 packets output, 657384 bytes, 0 underruns
0 output errors, 0 collisions, 11996 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial1/2 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
35152 packets output, 843648 bytes, 0 underruns
0 output errors, 0 collisions, 11997 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial1/3 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
27390 packets output, 657360 bytes, 0 underruns
0 output errors, 0 collisions, 11995 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Loopback0 is up, line protocol is up
Hardware is Loopback
Description: GRE Tunnel Source Interface
Internet address is 10.144.0.80/32
MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation LOOPBACK, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Description: GRE Tunnel Interface
Internet address is 10.144.2.26/30
MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
reliability 255/255, txload 1/255, rxload 113/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 10.144.0.80 (Loopback0), destination 10.144.254.1
Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled
Checksumming of packets disabled, fast tunneling enabled
Last input 00:00:01, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
11
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 4000 bits/sec, 5 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6192424 packets input, 894132772 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
57863 packets output, 4517542 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
.
- Follow-Ups:
- Re: Terminal Server Setup
- From: Aaron Leonard
- Re: Terminal Server Setup
- From: Aaron Leonard
- Re: Terminal Server Setup
- References:
- Terminal Server Setup
- From: MtbRoadie
- Re: Terminal Server Setup
- From: Aaron Leonard
- Terminal Server Setup
- Prev by Date: Re: Telnet to 800 series
- Next by Date: CRC & INPUT Errors
- Previous by thread: Re: Terminal Server Setup
- Next by thread: Re: Terminal Server Setup
- Index(es):
Relevant Pages
|
Loading