Slow Point to Point T1 Access Please Help

Hello,

We have a point to point T1 line going between our main office and a
branch, and the connection is very slow, I pasted the configurations
below of both routers. At the branch location we have 15 workstations
accessing the database over the T1 line, at our corp. office. The
database is by advantage (sybase now) and I believe it utilizes mostly
UDP for connections, it's a dos application that is installed locally
on each system and then connects to the database in the corporate
server. We have another 4 branches that have the same configs but most
of them have 10 workstations. I'm new to cisco and the guy who
configured the routers is not here anymore can you please take a look
and make any suggestions on how to make it work faster. Also under
available bandwidth it doesn't show the full 1.5 it shows 1.1 I
believe is that normal? I appreciate any help, thanks a lot in
advance!
###########Simi Valley Config#################
**Running Config*****
Building configuration...

Current configuration : 3281 bytes
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname simi
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 10 log
security passwords min-length 6
logging buffered 4096 debugging
logging console critical
enable secret 5 $1$z2Yg$4oeDvCfJEks6S9gZm9VT6.
enable password 7 04095E555A22485D
!
aaa new-model
!
!
aaa authentication login local_auth local
!
aaa session-id common
!
resource policy
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
no ip source-route
no ip gratuitous-arps
ip cef
!
!
no ip dhcp use vrf connected
!
ip dhcp pool SIMI
network 10.6.0.0 255.255.0.0
netbios-name-server 10.3.0.254
default-router 10.6.0.1
!
!
no ip bootp server
no ip domain lookup
ip domain name yourdomain.com
login block-for 1 attempts 100 within 100
!
username cisco privilege 15 secret 5 $1$ZMSn$9/qJDaP00Ox8L8pvUknNs/
!
!
!
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$
ip address 10.6.0.1 255.255.0.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
speed auto
full-duplex
no mop enabled
!
interface FastEthernet0/1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
shutdown
duplex auto
speed auto
no mop enabled
!
interface Serial0/0/0
ip address 192.168.1.111 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
!
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/0/0
ip route 10.3.0.0 255.255.0.0 192.168.1.100
ip route 10.3.0.251 255.255.255.255 10.3.0.1
!
no ip http server
ip http authentication local
ip http timeout-policy idle 5 life 86400 requests 10000
ip nat inside source list 1 interface FastEthernet0/0 overload
!
!
logging trap debugging
logging facility local2
snmp-server community public RO
no cdp run

****Version*****
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c),
RELEASE SO
FTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 25-Oct-05 17:10 by evmiller

ROM: System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)

simi uptime is 4 weeks, 3 days, 5 hours, 55 minutes
System returned to ROM by power-on
System image file is "flash:c1841-ipbase-mz.124-1c.bin"

Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory.
Processor board ID FTX0947Z2BA
2 FastEthernet interfaces
1 Serial interface
WIC T1-DSU
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31360K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

simi#
********Serial Info**********
simi#show int s0/0/0
Serial0/0/0 is up, line protocol is up
Hardware is GT96K with integrated T1 CSU/DSU
Internet address is 192.168.1.111/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 2/255
Encapsulation PPP, LCP Open
Open: IPCP, loopback not set
Keepalive set (10 sec)
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 4w3d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
2
Queueing strategy: weighted fair
Output queue: 0/1000/64/2 (size/max total/threshold/drops)
Conversations 0/74/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 17000 bits/sec, 9 packets/sec
5 minute output rate 7000 bits/sec, 7 packets/sec
33533354 packets input, 767112182 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
8 input errors, 8 CRC, 3 frame, 2 overrun, 0 ignored, 2 abort
27080721 packets output, 3552844864 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

simi#



###########Hollywood################


CORP2#sh run
Building configuration...

Current configuration : 756 bytes
!
version 12.2
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
no service password-encryption
!
hostname CORP2
!
logging buffered 4096 debugging
no logging console
enable secret 5 $1$EDuu$r.fjbiCbSabnjwqbFWnKN1
enable password 4123mka
!
ip subnet-zero
!
!
!
!
!
!
interface Ethernet0/0
ip address 10.3.0.2 255.255.0.0
full-duplex
!
interface Serial0/0
ip address 192.168.1.110 255.255.255.0
encapsulation ppp
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.3.0.1
ip route 10.1.0.0 255.255.0.0 10.3.0.1
ip route 10.2.0.0 255.255.0.0 10.3.0.1
ip route 10.4.0.0 255.255.0.0 10.3.0.1
ip route 10.6.0.0 255.255.0.0 Serial0/0
no ip http server
!
!
*******Version*************
CORP2#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(26), RELEASE
SOFTWARE (fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 31-Jul-04 04:57 by eaarmas
Image text-base: 0x8000808C, data-base: 0x80A1E540

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

CORP2 uptime is 11 weeks, 5 days, 1 hour, 39 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.122-26.bin"

cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes
of memory
..
Processor board ID JAD05060ZK0 (1117921095)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

************Serial Info**********
CORP2#sh int s0/0
Serial0/0 is up, line protocol is up
Hardware is PQUICC with Fractional T1 CSU/DSU
Internet address is 192.168.1.110/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Open
Listen: CDPCP
Open: IPCP
Last input 00:01:07, output 00:00:00, output hang never
Last clearing of "show interface" counters 11w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
1964
Queueing strategy: weighted fair
Output queue: 0/1000/64/1963 (size/max total/threshold/drops)
Conversations 0/60/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 2000 bits/sec, 2 packets/sec
5 minute output rate 11000 bits/sec, 2 packets/sec
64134072 packets input, 4142044605 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 7 giants, 0 throttles
44542 input errors, 1703 CRC, 20354 frame, 0 overrun, 0 ignored,
22485 abor
t
82315917 packets output, 1641942282 bytes, 0 underruns
0 output errors, 0 collisions, 28 interface resets
0 output buffer failures, 0 output buffers swapped out
8 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

.

Relevant Pages

  • Re: Slow Point to Point T1 Access Please Help
    ... interface FastEthernet0/0 ... DRAM configuration is 64 bits wide with parity disabled. ... minute output rate 7000 bits/sec, 7 packets/sec ... output buffer failures, ...
    (comp.dcom.sys.cisco)
  • Re: Input & Output bytes question
    ... I have a router with 3 serial interface and 1 ethernet interface, ... Serial0/0 is up, line protocol is up ... minute output rate 0 bits/sec, 0 packets/sec ... output buffer failures, ...
    (comp.dcom.sys.cisco)
  • Input & Output bytes question
    ... I have a router with 3 serial interface and 1 ethernet interface, ... Serial0/0 is up, line protocol is up ... minute output rate 0 bits/sec, 0 packets/sec ... output buffer failures, ...
    (comp.dcom.sys.cisco)
  • CRC & INPUT Errors
    ... Here is the output for Show Interface ... minute input rate 679000 bits/sec, ... minute output rate 112000 bits/sec, 159 packets/sec ... output buffer failures, ...
    (comp.dcom.sys.cisco)
  • Re: T1 lines go mad
    ... > Can you post the interface configs as well as a show interface for each end? ... Current configuration: 137 bytes ... Internet address is 192.168.245.1/30 ... output buffer failures, ...
    (comp.dcom.sys.cisco)