Re: Cisco dial backup with async interface

I think you need "dialer in-band" on the dialer interface not on the async
interface.

Scott

"SLECS99" <slecs99@xxxxxxxxxxx> wrote in message
news:1149038597.379146.227780@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi
I'm trying to configure two Cisco 2621 routers for dial backup. Main
interface is Fastethernet 0/0. Backup is dialer1. When router
TSFSDINLINRT1 int fast 0/0 goes down dialer 1 come up but there is no
dial action. I can dial trough manually so I know the phone circuits
all are operational. Anything missing in my config?

Main Site Router TSFSCCRT1

Ip subnet-zero
Ip cef

Interface loopback 0
No ip address

Interface FastEthernet0/0
Ip address 10.202.170.220 255.255.255.0
Speed auto
Full-duplex

Interface Async 1
No ip address
Encapsulation ppp
Dialer in-band
Dialer pool-member 1
Ppp authentication chap
Async mode dedicated
Async default routing

Interface async 2
No ip address

Username TSFSBANLINRT1 password tsfsdialbackup

Interface Dialer1
Ip unnumbered FastEthernet 0/0
Encapsulation ppp
Dialer pool 1
Dialer remote-name TSFSBANLINRT1
Dialer string 4903
Ppp authentication chap

Router rip
Redistribute connected
Network 10.0.0.0

Ip http server
Ip classless

Dialer-list 1 protocol ip permit

Line con 0
Line 1 2
Modem inout
Transport input all
Stopbits 1
Speed 115200
Flowcontrol hardware



Remote Site Router TSFSBANLINRT1

Ip subnet-zero
Ip cef

Interface loopback 0
No ip address

Interface FastEthernet0/0
Ip address 10.202.170.223 255.255.255.0
backup delay 15 15
backup interface Dialer1
speed auto
full-duplex

Interface Async 1
Ip unnumbered Fastethernet0/0
Encapsulation ppp
Dialer in-band
Dialer pool-member 1
Async mode dedicated
Ppp authentication chap
Async default routing

Interface Dialer1
Ip unnumbered FastEthernet 0/0
encapsulation ppp
dialer pool 1
dialer remote-name TSFSCCRT1
dialer string 29617181
ppp authentication chap

username TSFSCCRT1 password tsfsdialbackup

Interface Vlan1
Ip address 10.202.173.200 255.255.255.0

Router rip
Redistribute connected
Network 10.0.0.0

Ip http server
Ip classless

Dialer-list 1 protocol ip permit

Line 1
Modem inout
Transport input all
Autoselect ppp
Stopbits 1
Speed 115200
Flowcontrol hardware



.

Relevant Pages

  • Re: ADSL with ISDN backup
    ... I never used before ATM interface for connecting to ... your router will use next route-map 'set ip next-hop' statement (you will ... your case you have to specifie one of your dialer interfaces:(... ...
    (comp.dcom.sys.cisco)
  • ISDN Dailer Chap problem
    ... For some reason the Dialer interface ppp keeps getting refused due to ... a CHAP error. ... crypto map Genericmap2 1 ipsec-isakmp ...
    (comp.dcom.sys.cisco)
  • Object tracking - What am i doing wrong?
    ... I have been trying to get an ISDN circuit to dial up and connect 2x 1841 ... Cisco routers together if the primary adsl interface fails. ... encapsulation aal5mux ppp dialer ... access-list 101 permit ip 192.168.1.0 0.0.0.255 any ...
    (comp.dcom.sys.cisco)
  • Pix 506e - 1721 problem
    ... I need to change my border router to a 1721 with one sdsl and one adsl ... interface this then connects to a pix 506e but the 1721 has been ... My problem - is that the pix 506e has a public ip and is configured to ... encapsulation aal5mux ppp dialer ...
    (comp.dcom.sys.cisco)
  • Here is a tutorial on Cisco dialup
    ... outside" on the Dialer and/or Async interfaces ... Cisco Configs - Using AUX port and analog modem to dialup ISP ... Async Interface ...
    (comp.dcom.sys.cisco)