problem with IOS

hi everybody
I have problem with my 2620, I upgraded an IOS version to 12.4.3 and from
this point my router on every start decompressing the image. I made all
configuration than copy to startup-config but always the same.

here is print when router starts:



Self decompressing the image :
#################################################
################################################################################
################################################################################
########################################## [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
000094 0X000B3B80 C2600 Single Fast Ethernet
0X00098670 public buffer pools
0X00211000 public particle pools
TOTAL: 0X0035D1F0

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 3Mb.
Using 5 percent iomem. [3Mb/64Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, C2600 Software (C2600-ENTBASEK9-M),
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 22-Jul-05 05:09 by hqluong
Image text-base: 0x80008098, data-base: 0x818B8158

Port Statistics for unclassified packets is not turned on.

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found
at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@xxxxxxxxxx

Cisco 2620 (MPC860) processor (revision 0x200) with 62091K/3445K bytes of
memoryLY 20000 usec,e" counters never20 (MPC860) proce
..
Processor board ID JAD051009BP (589753981)
M860 processor: part number 0, mask 49 software5
1 FastEthernet interface
dspu
1 Serial interfacewnStream Physical
1 ISDN Basic Rate interface
32K bytes of NVRAM. Keepalive set (10
16384K bytes of processor board System flash (Read/Write)
Modify enable password parametersevererent



Press RETURN to get started!


*Mar 1 00:00:17.255: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed
state t
*Mar 1 00:00:17.259: %LINK-3-UPDOWN: Interface Serial0/0, changed state to
down

*Mar 1 00:00:18.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthern
et0/0, changed state to down
*Mar 1 00:00:18.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0,
changed state to down
*Mar 1 00:00:19.675: %LINK-5-CHANGED: Interface BRI0/0, changed state to
admini
stratively down
*Mar 1 00:00:20.675: %LINEPROTO-5-UPDOWN: Line protocol on Interface
BRI0/0, ch
anged state to down
*Mar 1 00:00:20.919: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:30:05.583: %LINK-5-CHANGED: Interface Serial0/0, changed state to
adm
inistratively down
*Mar 1 00:30:06.139: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (C2600-ENTBASEK9-M), Version 12.4(3),
RELEASE
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 22-Jul-05 05:09 by hqluong
*Mar 1 00:30:06.143: %SNMP-5-COLDSTART: SNMP agent on host Router is
undergoing
a cold start
*Mar 1 00:30:14.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthern
et0/0, changed state to up
Router>



if you can help me thanks in advance
WZ


.