Re: cisco 828 router

is there a way of resetting the router to its factor default setting so i
can restart the configuration?

thanks

andy

"andy everett" <ae@xxxxxxxxxxxxx> wrote in message
news:US5Xf.33834$UH4.19027@xxxxxxxxxxxxxxxxxxxxxxxxxxxx
hi

can someone please help me on this as the reseller i bought my router from
is useless at support.

my current config is:

router#show configuration
Using 1680 out of 131072 bytes
!
version 12.3
no parser cache
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$/GYO$St6Bqigg6Wr3cDoNEND/a0
enable password anya1234
!
no aaa new-model
ip subnet-zero
!
!
!
!
interface Ethernet0
ip address 10.10.10.1 255.255.255.0
no ip proxy-arp
ip nat inside
ip dhcp relay information trusted
no cdp enable
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl equipment-type CPE
dsl operating-mode GSHDSL symmetric annex B
dsl linerate AUTO
pvc 0/38
encapsulation aal5snap
!
pvc 8/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Dialer0
ip address negotiated
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap callin
ppp chap hostname <un>
ppp chap password 0 <pw>
ppp pap sent-username <un> password 0 <pw>
!
router rip
redistribute connected
network 10.0.0.0
!
ip nat inside source list 1 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
access-list 1 permit 10.10.10.0 0.0.0.255
access-list 1 permit 0.10.10.1 255.0.0.0
access-list 23 permit any
dialer-list 1 protocol ip permit
no cdp run
snmp-server community public RO
snmp-server enable traps tty
!
line con 0
exec-timeout 120 0
transport preferred all
transport output all
stopbits 1
line vty 0 4
access-class 23 in
exec-timeout 120 0
password anya1234
login local
transport preferred all
transport input all
transport output all
!
scheduler max-task-time 5000
!
end

the settings I need are PPPoA, with VC as the encapsulation, VPI is 0 and
VCI is 38, DNS servers are 195.74.102.146 and 195.74.102.147



Andy




.

Relevant Pages

  • DSL Line dropping, need cable pull for ATM interface to come alive
    ... All seems well apart form one circuit where the installed Cisco 828 ... About 30 seconds after the cable is reconnected the router ... encapsulation aal5mux ppp dialer ... transport preferred all ...
    (comp.dcom.sys.cisco)
  • cisco 828 router
    ... can someone please help me on this as the reseller i bought my router from ... encapsulation aal5mux ppp dialer ... access-list 1 permit 0.10.10.1 255.0.0.0 ... transport preferred all ...
    (comp.dcom.sys.cisco)
  • Re: Cisco 3660 dial-in problem
    ... ~ I have a problem with ISDN Dial-in to 3660 Cisco router. ... with my router configuration? ... a dialer profile is for a connection to exactly ONE peer ...
    (comp.dcom.sys.cisco)
  • Re: Cisco 3660 dial-in problem
    ... ~ configured a PRI int for ISDN and i have defined one dialer profile. ... ~ have almost 35 remote sites calling to router (computers with ISDN ... Is it something wrong with my router configuration? ... a dialer profile is for a connection to exactly ONE peer (possibly ...
    (comp.dcom.sys.cisco)
  • Re: Cisco 3660 dial-in problem
    ... ~ configured a PRI int for ISDN and i have defined one dialer profile. ... ~ have almost 35 remote sites calling to router (computers with ISDN ... Is it something wrong with my router configuration? ... a dialer profile is for a connection to exactly ONE peer (possibly ...
    (comp.dcom.sys.cisco)