Vlans on a 2900 series XL switch

Hi,

I have a 2900 series XL switch I bought in a bundle for my home lab to
help with my ccna studies. I am trying to play around with vlans but
any of the commands I am reading about do not work. It says to use the
"set vlan" and "set vtp" commands to configure vlans on the cisco site,
but the only command mine has starting with "set" is setup. Spent a few
hours now reading and getting a little frustrated. Any help on how to
set up vlans on this device would be greatly appreciated. I have pasted
the output from show version below.
Also when I first booted the device it started up asking if I wanted to
use command line or menus, after I defaulted the device I can not get
back to the config menu, I was going to try and set up a vlan domain
that way then look at the config to see what changes it made and try
using them commands but now I can not get into the config menu either.
How do I get back into the config menu also please?

Thanks

Regards,

Vos

Cisco Internetwork Operating System Software
IOS (tm) C2900XL Software (C2900XL-H-M), Version 11.2(8)SA5, RELEASE
SOFTWARE (f
c1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 23-Mar-99 11:52 by rheaton
Image text-base: 0x00003000, data-base: 0x001D0068

ROM: Bootstrap program is C2900XL boot loader

Switch uptime is 20 minutes
System restarted by power-on
System image file is "flash:c2900XL-h-mz-112.8-SA5", booted via


cisco WS-C2924M-XL (PowerPC403GA) processor (revision 0x11) with
8192K/1024K byt
es of memory.
Processor board ID 0x10, with hardware revision 0x03
Last reset from power-on

Processor is running Standard Edition Software
24 Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:D0:58:CF:DA:00
Motherboard assembly number: 73-3425-08
Power supply part number: 34-0920-01
Motherboard serial number: FAA03179GKG
Power supply serial number: PHI031002KD
Model revision number: A0
Model number: WS-C2924M-XL-A
System serial number: FAA0321F0ER
Configuration register is 0xF

.

Relevant Pages

  • Re: Not seeing all VLANS
    ... The 2 2960's are not seeing all the VLANs and I can't work out why ... Okay, so first part, is your VTP isn't working. ... and not matching the config rev on the VTP server. ... With the switch in VTP client mode, it won't automake the VLAN into ...
    (comp.dcom.sys.cisco)
  • Thoughts on PIX v7 cont...
    ... few commands did not "port" over properly. ... -Since we have a FO config - turn off SECONDARY and upgrade the ... turn off the PRIMARY and upgrade the SECONDARY. ... PIX config is 4800 lines long, so it was only about 2%. ...
    (comp.dcom.sys.cisco)
  • Re: Cisco 2950 Issue
    ... As the virtual MAC is not known on any port the switch has to ... The 2950 config is very basic, ... does the ISA know how to get back to your other vlans, ... but for now it's all 1 x flat VLAN. ...
    (comp.dcom.sys.cisco)
  • [patch 2/2] Touchscreen support for sharp sl-5500
    ... +config TOUCHSCREEN_COLLIE ... * Switch to pressure mode, ... * Switch to X position mode and measure Y plate. ... +static int ucb1x00_ts_open ...
    (Linux-Kernel)
  • Re: [patch 2/2] Touchscreen support for sharp sl-5500
    ... +config TOUCHSCREEN_COLLIE ... * Switch to pressure mode, ... * Switch to X position mode and measure Y plate. ... +static int ucb1x00_ts_open ...
    (Linux-Kernel)