Re: AS5400 configuration help

Just a quick one, I had alot of trouble last time until I upgraded IOS.

Also why don't you try local authentication first.

I'll post send you one of my working configs if you need okay.

D

FixitDave wrote:
I'm trying to setup an AS5400 for in/out modem/ISDN access, firstly I'd
just like to configure for modem access, but when I dial into it I get
the following output (debug isdn q931, isdn error & spe modem
errors)...The dialing modem just keeps whistling then responds with 'no
carrier'

Jan 3 04:56:56.826 gmt: ISDN Se7/0:15 Q931: RX <- SETUP pd = 8
callref = 0x0001
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Called Party Number i = 0x81, '376800'
Plan:ISDN, Type:Unknown
Jan 3 04:56:56.826 gmt: PM_ST_MODEM_ERR: pm_modem_mgmt_get_modem_parm:
no hwidb/tty
Jan 3 04:56:56.830 gmt: ISDN Se7/0:15 Q931: TX -> CALL_PROC pd = 8
callref = 0x8001
Channel ID i = 0xA98381
Exclusive, Channel 1
Jan 3 04:56:56.830 gmt: ISDN Se7/0:15 Q931: TX -> ALERTING pd = 8
callref = 0x8001
Jan 3 04:56:56.834 gmt: ISDN Se7/0:15 Q931: TX -> CONNECT pd = 8
callref = 0x8001
Jan 3 04:56:56.934 gmt: ISDN Se7/0:15 Q931: RX <- CONNECT_ACK pd = 8
callref = 0x0001

****debug waits here for a while, then 'no carrier' on dialing
modem****

Jan 3 04:57:52.247 gmt: ISDN Se7/0:15 Q931: RX <- DISCONNECT pd = 8
callref = 0x0001
Cause i = 0x8090 - Normal call clearing
Progress Ind i = 0x8288 - In-band info or appropriate now
available
Jan 3 04:57:52.247 gmt: ISDN Se7/0:15 Q931: TX -> RELEASE pd = 8
callref = 0x8001
Jan 3 04:57:52.307 gmt: ISDN Se7/0:15 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x0001
Jan 3 04:57:53.327 gmt:
%MODEMCALLRECORD-6-PM_TERSE_CALL_FAILED_RECORD: DS0
slot/contr/chan=7/0/1, slot/port=1/13, call_id=E, calli
ng=(n/a), called=376800, time=0, finl-state=Half Duplex Train,
disc(modem)=1F06 <unknown>/Requested by host/network indicated discon
nect
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-TRACE_HDR:

Modem 1/13 Events Log:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 1 00:03:47.843 gmt: Port State Reached:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 1 00:03:47.847 gmt: Port State Reached:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-CSM_IC_CALLED_NUM:
Jan 3 04:56:56.830 gmt: ISDN incoming called number: 376800
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 3 04:56:56.834 gmt: Port State Reached:
Jan 3 04:57:53.327 gmt: %PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT:
Jan 3 04:56:56.942 gmt: Port State Reached:
Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
Jan 3 04:56:56.942 gmt: Modem State event:
State: Connect
Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
Jan 3 04:56:59.366 gmt: Modem State event:
State: V.8bis Exchange
Jan 3 04:57:53.331 gmt: %PM_MODEM_HIST-7-MODEM_STATE_EVT:
Jan 3 04:57:00.638 gmt: Modem State event:
State: Quick Connect
Jan 3 04:58:00.291 gmt: %CALLTRKR-6-CALL_RECORD: ct_hndl=23,
service=None, origin=Answer, category=Modem, DS0 slot/port/ds1/chan=7/
0/0/0, called=376800, calling=(n/a), resource slot/port=1/13,
userid=(n/a), ip=0.0.0.0, mask=0.0.0.0, account id=165, setup=01/03/20
00 04:56:54, conn=0.11, phys=0.00, service=0.00, authen=0.00,
init-rx/tx b-rate=64000/64000, rx/tx chars=0/0, time=55.42, disc subsy
s=ISDN, disc code=0x10, disc text=Normal call clearing
Jan 3 04:58:00.291 gmt: %CALLTRKR-6-MODEM_CALL_REC: ct_hndl=23, prot:
last=SYNC Mode, attempt=SYNC Mode, comp: last=None, atmp= Non
e, std: last=V.21, attempt=V.21, init=V.21, snr=0, sq=0, rx/tx:
chars=0/0, ec: rx/tx=0/0, rx bad=0, rx/tx b-rate: last=13408/13408,
low=13408/13408, high=300/300, desired-client=(n/a)/(n/a),
desired-host=(n/a)/(n/a), retr: local=0, remote=0, fail=0, speedshift:
lo
cal up/down=0/0, remote up/down=0/0, fail=0, v90: stat=No Attempt,
client=(n/a), fail=None, time(sec)=0, disc reason=0x1F06
Jan 3 04:58:00.291 gmt: %CALLTRKR-6-MODEM_LINE_CALL_REC: ct_hndl=23,
rx/tx levl=0/255, phase-jit: freq=0.0, levl=0, far-end echo-le
vl=0, freq offst=0.0, phase-roll=0.0, round-trip=0, d-pad=None, d-pad
comp=0, rbs=0, const=None rx/tx: sym-rate=0/0, carr-freq=0/0,
trel-code=0/0, preemph-index=0/0, rx/tx: const-shape=Off/Off,
nonlin-encode=Off/Off, precode=Off/Off, xmit levl-reduct=0/0, shape=0x
0000000000000000000000000000000000000000000000000000
Jan 3 04:58:00.295 gmt: %CALLTRKR-6-MODEM_INFO_CALL_REC: ct_hndl=23,
general info=0x0, rx/tx link-layer=0/0, NAKs=0/0, rx/tx ppp-sl
ip=0/0, bad ppp-slip=0, proj max rx b-rate: client=0, host=0, rx/tx:
max neg I frame=0/0, neg window=0/0, T401 timeouts=0, tx window
closures=0, rx overruns=0, retrans frames=0, v110: rx good=0, rx
bad=0, tx=0, sync-lost=0, ss7/cot=0x00, v42bis size: dict=0, strin
g=0, test err=0, reset=0, v0 synch-loss=0, mail lost: host=0, sp=0,
diag=0x00000000000000000000000000000000
Jan 3 04:58:00.295 gmt: %CALLTRKR-6-MODEM_NEG_CALL_REC: ct_hndl=23,
v90 train=0x00000000, v90 sgn-ptrn=0x00000000, state trnsn=0x00
00000000000000000000000000000000000000000000000000000000000000,
phase2=0x00000000000000000000000000000000000000000000000000000000000
00000000000000000000000000000000000000000000000000000

My config is (some lines have been left out to try and reduce the post
length)...
version 12.3
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service compress-config
!
hostname HDWD-GW-DIAL1
!
no boot startup-test
enable secret 5 xxxxxxxxxxxxxxxxxxxxx
!
username administrator password 7 xxxxxxxxx
username manager privilege 6 password 7 xxxxxxxxx
username test password 0 test
!
!
resource-pool disable
clock timezone gmt 0
clock summer-time bst recurring
clock calendar-valid
calltracker enable
calltracker history max-size 200
calltracker call-record verbose
spe call-record modem
!
spe default-firmware spe-firmware-1
aaa new-model
!
!
aaa authentication login netenguk group tacacs+ line
aaa authentication login console group tacacs+ none
aaa authentication ppp default group tacacs+ none
aaa authentication ppp ppptac group tacacs+ none
aaa authorization exec netenguk group tacacs+ none
aaa authorization commands 15 netenguk group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
ip subnet-zero
ip domain name 555.co.uk
ip name-server 5.5.31.7
ip name-server 5.5.95.7
!
ip cef
ip address-pool local
ip dhcp-server 5.5.31.7
ip dhcp-server 5.5.95.7
mpls ldp logging neighbor-changes
isdn switch-type primary-net5
isdn voice-call-failure 0
no scripting tcl init
no scripting tcl encdir
!
!
!
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
!
!
!
!
!
!
!
controller E1 7/0
framing NO-CRC4
pri-group timeslots 1-30
!
controller E1 7/1
!
controller E1 7/2
!
controller E1 7/3
!
controller E1 7/4
!
controller E1 7/5
!
controller E1 7/6
!
controller E1 7/7
bridge irb
!
!
interface Loopback0
ip address 192.168.240.231 255.255.255.255
no ip mroute-cache
!
interface FastEthernet0/0
ip address 5.5.20.2 255.255.255.0
no ip mroute-cache
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
clockrate 2000000
!
interface Serial7/0
no ip address
shutdown
!
interface Serial0/1
no ip address
shutdown
clockrate 2000000
!
interface Serial7/0:15
no ip address
encapsulation ppp
no ip route-cache
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
isdn calling-number 376800
no fair-queue
no cdp enable
!
interface Group-Async0
ip unnumbered FastEthernet0/0
encapsulation ppp
no ip mroute-cache
async mode dedicated
peer default ip address pool pool_dialup
ppp authentication chap pap callin
group-range 1/00 1/107
hold-queue 75 in
!
interface Group-Async1
ip unnumbered FastEthernet0/0
no ip route-cache
no ip mroute-cache
dialer in-band
dialer rotary-group 1
async default routing
async mode dedicated
peer default ip address pool pool_dialup
ppp authentication chap pap callin
group-range 3/00 3/59
!
interface Dialer1
ip unnumbered FastEthernet0/0
encapsulation ppp
no ip mroute-cache
dialer in-band
dialer idle-timeout 2700 either
dialer watch-group 1
dialer-group 1
peer default ip address pool pool_dialup
no fair-queue
no cdp enable
ppp authentication chap pap callin
ppp multilink
!
ip local pool pool_dialup 5.5.20.245 5.5.20.250
ip classless
ip route 0.0.0.0 0.0.0.0 5.5.20.254
no ip http server
no ip http secure-server
!
!
dialer-list 1 protocol ip permit
!
voice-port 7/0:D
!
ss7 mtp2-variant Bellcore 0
ss7 mtp2-variant Bellcore 1
ss7 mtp2-variant Bellcore 2
ss7 mtp2-variant Bellcore 3
!
line 1/00 1/107
exec-timeout 0 0
no flush-at-activation
modem InOut
rotary 1
transport input all
line 3/00 3/59
exec-timeout 0 0
no flush-at-activation
modem InOut
rotary 1
transport input all
!
scheduler allocate 10000 400
end

.

Relevant Pages

  • Re: AAA authentication woes
    ... I have a sticky problem with AAA authentication and I'm either reading ... The reason this fails is the debugs show that the incoming interface is ... the dialer interface D3 only takes place after sucessful authentication ... aaa authentication login default group tacacs+ local ...
    (comp.dcom.sys.cisco)
  • Re: Strange problem 827
    ... your internet provider attempts to establish a connection to YOU. ... You need to configure ppp authentication on ... after a while Atm goes down so the Dialer ... Interface tries to connect again. ...
    (comp.dcom.sys.cisco)
  • AS5400 configuration help
    ... just like to configure for modem access, but when I dial into it I get ... controller E1 7/0 ... interface FastEthernet0/0 ... dialer rotary-group 1 ...
    (comp.dcom.sys.cisco)
  • 876W Wireless
    ... interface BRI0 ... encapsulation aal5mux ppp dialer ... authentication key-management wpa ... bridge-group 1 subscriber-loop-control ...
    (comp.dcom.sys.cisco)
  • Re: Machine Authentication not working with wireless clients and I
    ... after many hours with tech support at Microsoft and Aruba we finally ... Authenication-Methods-802.1x,my controller had a checkbox set for inner eap ... authentication, just the same error as before, about invalid account. ... What I would do is create a group of wireless enabled computers. ...
    (microsoft.public.internet.radius)