Re: Catalyst 3750 Static Routes

Does this 3750 switch have ip address from all the subnets? If it has you
need only ip routing, if you need
some network to be routed to pix, you should use ip route net mask
and_next_hop_address_pix
Put show runn here.

>I am attempting to enable routing on a Catalyst 3750 (EMI) switch.
> I only need to do static routing, currently routing is entirely
> disabled.
>
> And the default gateway is set to : 192.168.2.254
>
> The network that is routed to this gateway is 10.10.66.0 and the
> routing is done through a PIX515E.
>
> Here is a diagram:
>
> [192.168.2.254]
> |
> |
> ([192.168.2.1] <outside> PIX <inside> [10.10.66.1])
> |
> |
> [10.10.66.0]
>
> This is all done with one switch and two VLANs.
>
> Nodes on the 10.10.66.0 network have 10.10.66.1 as their default
> gateway.
> The PIX uses 192.168.2.254 as its default route.
>
> I have another network, 10.10.42.0, that I want to connect to this
> switch, and allow for IP traffic
> between 10.10.66.0 and 10.10.42.0.
>
> The 10.10.42.0 network is connected to a Cisco 2960 switch, which is
> unlinked to the 3750 switch.
>
> I've been pouring over the 3750s Configuration Guide and I think I've
> figured out the proper sequence
> of commands to enable this type of routing.
>
> Here are the commands:
>
> 3750>ip routing
> 3750>route static
> 3750>ip route 0.0.0.0 0.0.0.0 10.10.66.1 1
> 3750>ip route 10.10.42.0 255.255.255.0 10.10.42.3 1
>
> 10.10.66.1 and 10.10.42.3 are both ports in VLAN 2.
>
> Will this configuration properly route IP traffic destined for outside
> networks to 10.10.66.1,
> IP traffic destined for 10.10.42.0 to 10.10.42.3 and IP traffic
> destined for 10.10.66.0 to the
> right node on the switch?
>


.

Relevant Pages

  • Re: AIX 1.3 Failures and Fables
    ... DESTINATION GATEWAY FLGS REFCNT USE INTERFACE ... Is my interpretation of the AIX 1.3 #man route correct? ... Manually manipulates the routing tables. ... Is the destination host or network. ...
    (comp.sys.ibm.ps2.hardware)
  • Re: AIX 1.3 Failures and Fables
    ... I don't know if 1.3 has SMIT or its equivalent but there should be some way to add a default gateway which is your router. ... Is my interpretation of the AIX 1.3 #man route correct? ... Manually manipulates the routing tables. ... Is the destination host or network. ...
    (comp.sys.ibm.ps2.hardware)
  • Re: Very small network question...
    ... If you have something between them (like a switch or hub) you need 'normal' ... You have to set the gateway ONLY if you have a gateway in your network. ... an Ethernet-enabled target board with a static IP. ...
    (comp.os.linux.networking)
  • Re: Misbehaving routing tables
    ... The metrics are supposed to give priority to ... I have including a portion of the routing table below immediately following ... Default Gateway: 192.168.10.254 ... I did notice that the default gateway is the 192.168.10.x network, ...
    (microsoft.public.windows.server.networking)
  • Re: 5500 transfer
    ... network traffic between subnets connected by the very same router. ... when high loads of network traffic are crossing the switch. ... The Cisco Catalyst 5500 is available as a routing switch only if a RSM ... interface vlan 2 ...
    (comp.dcom.sys.cisco)