OSPF issues on Ethernet Interfaces



Hi All,

I have recently migrated from two Cisco4700's to two Cisco 2821's.
The new router is not able to form an OSPF network adjacency.
The two main differences from the old routers to the new ones is:
1).Instead of V.35 WAN connections,FE connections.
2).The other difference is that I have a 16port FE switch module.

The error I am getting is that the OSPF process cannot form an
adjacency.
I ran a debug and it appeared that I was having an MTU issue, so I
applied the ip ospf mtu-ignore statement which didn't resolve the
issue.

Here is the output form the debug:

Aug 10 05:13:20.916: IP: s=10.2.195.2 (Vlan6), d=224.0.0.5, len 80,
rcvd 0all
Aug 10 05:13:22.084: IP: s=10.2.172.81 (local), d=224.0.0.5
(GigabitEthernet0/0), len 80, sending broad/multicast
Aug 10 05:13:22.160: IP: s=10.2.172.82 (GigabitEthernet0/0),
d=224.0.0.5, len 80, rcvd 0
Aug 10 05:13:22.944: IP: s=10.2.195.1 (local), d=224.0.0.5 (Vlan6), len
80, sending broad/multicast
Aug 10 05:13:22.944: IP: s=10.2.195.2 (Vlan6), d=10.2.195.1, len 64,
rcvd 0
Aug 10 05:13:22.944: OSPF: Rcv DBD from 10.2.171.22 on Vlan6 seq 0x193
opt 0x52 flag 0x7 len 32 mtu 1500 state EXCHANGE
Aug 10 05:13:22.944: OSPF: Send DBD to 10.2.171.22 on Vlan6 seq 0x193
opt 0x52 flag 0x2 len 112
Aug 10 05:13:22.944: IP: s=10.2.195.1 (local), d=10.2.195.2 (Vlan6),
len 144, sending


Aug 10 07:09:57.580: OSPF: Cannot see ourself in hello from 10.2.171.22
on Vlan6, state INIT
Aug 10 07:09:57.584: OSPF: Neighbor change Event on interface Vlan6
Aug 10 07:09:57.584: OSPF: DR/BDR election on Vlan6
Aug 10 07:09:57.584: OSPF: Elect BDR 10.2.171.21
Aug 10 07:09:57.584: OSPF: Elect DR 10.2.171.21
Aug 10 07:09:57.584: OSPF: Elect BDR 0.0.0.0
Aug 10 07:09:57.584: OSPF: Elect DR 10.2.171.21
Aug 10 07:09:57.584: DR: 10.2.171.21 (Id) BDR: none
Aug 10 07:09:57.584: OSPF: Reset Vlan6 flush timer
Aug 10 07:09:57.584: OSPF: Remember old DR 10.2.171.22 (id)
Aug 10 07:09:58.084: OSPF: No full nbrs to build Net Lsa for interface
Vlan6
Aug 10 07:09:58.084: OSPF: Reset old DR on Vlan6

Any tips or suggestions would be greatly appreciated.

Thanks.

Jack.

.



Relevant Pages

  • Re: ospf network statement - correct use (long)
    ... network statement for OSPF should be used with subnets on which you ... another router. ... Snippets of the basic interface config for each router are as follows: ... The only routes that are "internal" are those where OSPF is running on the ...
    (comp.dcom.sys.cisco)
  • Re: basic ospf question!
    ... router ospf 100 ... what I saw was that ospf would learn about the neighbor but no routes ... ' redistribute static' to both routers and I saw OSPF type E2 routes ...
    (comp.dcom.sys.cisco)
  • FreeBSD/zebraOSPF not updating routingtables
    ... I am trying to get OSPF working but it won't work. ... but no routing tables are updated. ... description dummy/loopback interface ... OSPF Routing Process, Router ID: ...
    (comp.unix.bsd.freebsd.misc)
  • Re: rapid network reconvergence technology?
    ... Is there technology available that will provide much faster router ... OSPF convergence, like most, is composed of two major components. ... Link down depends on the link technology and topology. ... but it depends on the network. ...
    (comp.dcom.sys.cisco)
  • Re: Assertion in Python
    ... OSPF not enabled on this interface ... Router ID 192.168.1.2, Network Type BROADCAST, Cost: ... No backup designated router on this network ...
    (comp.lang.python)