Re: What is 'drive strength' for? (Spartan 3)

Paul,

Drive strength sets the worst case minimum current that will be available.

Worst case is measured at hottest temperature, worst (slowest) process, and lowest IO voltage.

So, for example, if we are designing ICs that have to meet mil spec (125C), over all process, and over +/- 10% IO voltage variation, the actual current at 25C, nominal process, and nominal IO voltage will be substantially larger.

If you use DCI, you can actually set the output resistance by setting the drive impedance with the external resistors....but Spartan 3 does not have DCI, so that won't help you there. Sorry. DCI (digitally controlled impedance) is a useful feature offerred in the Virtex line, but not in the Spartan line.

So, all you have to play with is drive strength (you could set it to 2 mA, or the lowest setting), and the Vcco voltage. By setting the drive to the lowest possible setting for the highest possible Vcco (eg 2 mA at 3.3 V) by lowering the voltage to 2.5V, you will now be much lower current than the operation at 3.3V (and the IOB will still work just fine, as the difference between 3.3V and 2.5V IO standards is how many transistors to turn on in parallel: it takes more to drive the same current at lower voltages).

The brightness will vary with chip to chip (process variations) and also will vary with chip temperature.

Austin

PS: did you know that the Christmas Lights video that went around recently was done in Cincinnati, Ohio, and used Spartan 3 demo kits to control banks of triacs? What some people have time to do is amazing!

http://www.snopes.com/photos/arts/xmaslights.asp




Paul Boven wrote:

Hi everyone,

I'm building a circuit that will be driving quite a few (>100) LEDs, multiplexed into 3 or 4 groups, so up to 40 at the same time.
Can I use the Spartan 3 'Current drive' option to limit drive current to these LEDs to e.g. 24 mA ? I'm hoping to limit the number of external components that I'll need.
I've set the IO standard of the ports in question to LVCMOS33 and set 24mA, but the port drives at least 70mA trough a LED and amp-meter connected to ground. Setting a lower value for drive current does decrease the drive, but it stays significantly above the value I set - and I'd rather not ruin my LEDs or, even worse, FPGA.

So I'm probably misunderstanding the way 'drive limit' is set or supposed to be used. Could anyone enlighten me?

Regards, Paul Boven. 
.

Relevant Pages

  • Re: led dimmer circuit
    ... This current source drives a current through R3 and R4 ... and thereby sets the linearly adjustable voltage to the base of Q2, ... Q2's emitter voltage sets the current through R5 and therefore also ... be used, though, if several LEDs are to be used in series. ...
    (sci.electronics.design)
  • Re: led dimmer circuit
    ... This current source drives a current through R3 and R4 ... and thereby sets the linearly adjustable voltage to the base of Q2, ... Q2's emitter voltage sets the current through R5 and therefore also ... be used, though, if several LEDs are to be used in series. ...
    (sci.electronics.design)
  • Re: led dimmer circuit
    ... This current source drives a current through R3 and R4 ... and thereby sets the linearly adjustable voltage to the base of Q2, ... Q2's emitter voltage sets the current through R5 and therefore also ... be used, though, if several LEDs are to be used in series. ...
    (sci.electronics.design)
  • Re: More updates on the Bridgeport conversion project
    ... saturable reactors were calling for maximum voltage for fast ... full speed from the servo motors you have. ... just sell those Bosch drives, ... inhibit function on the drives that could be triggered by limit ...
    (rec.crafts.metalworking)
  • Re: More updates on the Bridgeport conversion project
    ... saturable reactors were calling for maximum voltage for fast ... seems to be one phase transformer. ... full speed from the servo motors you have. ... just sell those Bosch drives, ...
    (rec.crafts.metalworking)