Re: Confused on Folder Sharing



MB_ wrote:

OK -- somehow I am screwing this up.

I currently have a Dell Dim 2400. It is set up for Broadband with a Lynksys router.

I also have a new Dell Inspiron 2200 with a wireless card.

All works perfectly and I've also taken some reasonable security precautions (MAC filtering, disabling SSID broadcasting, etc).

Now, here is what I want to do.

I have a FOLDER on my desktop. I would like to be able to share this folder. That is, I want to be able to use this folder with my desktop or with my wireless. Let's suppose this folder is c:\george\washington

So, now I am attempting to join the wonderful world of file sharing and I thought I did it correctly, but maybe not.

Firstly, I turned on my desktop and then the laptop. I ran Network Setup Wizard on my desktop. When I ran thru the steps, perhaps I should have chosen that this computer hooks up directly to the internet. But I chose that it hooks up to the internet via a residential gateway (the picture in the example seemed closer to what I had, but I'm not sure). I then followed instructions and rebooted the desktop. I then ran the Wizard on the Wireless and I chose the same thing. (I suspect these choices might not be correct!)

I then rebooted the wireless.

I then got on the desktop, right clicked the aforementioned file in Windows Explorer and designated it to be shared by all computers on the network.

Well, when I check on the desktop under Windows Explorer it does appear that the folder is enabled for sharing.

But I cannot find that shared folder anywhere when I use my Wireless.

Suggestions??

Also, if I have to change some setting, do I just start all over and re-run the Network Setup Wizard?

Mel


Mel, could you clarify something: are you attempting to share the directory over your local network (between 2 computers behind the same router) or across the interner?

I'm going to assume behind the same router (although both are possible). Can you "see" the host (the computer sharing the directory) from the client? The easiest check is (from the client) to go to a DOS prompt (Start -> cmd [ok]) and type: ping $hostname (where $hostname is the name of the host sharing the directory). If you can see it, ping will return a time in milliseconds. If you can't see the host by its hostname, try pinging its IP address (to determine the address, on the host in the DOS prompt run ipconfig). If you can't see the IP chances are it's a firewall problem; if you can, try to "find" the host from the client (Start -> Search -> For Files or Folders -> Computer or People). Now search the hostname (if you could ping it) or the IP Address. You should be able to figure it out from here.

Another thought I have is are you certain you're on your wireless network (and not your neighbors)? This may seem like a stupid question, but I can literally detect 39 wireless networks (I live in a complex when I'm at school) from my couch and if I used the default settings for my router I'd probably end up on my neighbor's network since it may have the same SSID. I'd recommend setting a unique SSID for multiple reasons; but at the very least, do it so you don't end on your neigbors network withoud knowing it.
.




Relevant Pages

  • 2wire router configuration
    ... firewall on this router and to configure my network ... Go to Home Network -> Advanced Settings ... X Default DHCP Pool ... Configure host to use DHCP with host name sent ...
    (comp.unix.bsd.freebsd.misc)
  • Re: Sharing a Printer
    ... that if I can fix that problem, the sharing problem will be easy to fix. ... The router has a firewall, but it is set to allow all LAN ... The following assumes that the PCs on the network are communicating with ... My Dlink router has a base address of 192.168.0.1 and the computers ...
    (microsoft.public.windowsxp.general)
  • Re: Networking Questions
    ... The DNS address is sent as a secondary element, mostly because there's no point for nearly all internet connections without DNS. ... The PC asks for an address by sending a DHCP request out the route to the DSL device which is either a modem or a router. ... No need for DNS until host names get involved and those hosts are on a different network segment. ... DNS is mostly just a very glorified hosts table that includes addresses in all network address ranges. ...
    (comp.sys.ibm.as400.misc)
  • Re: Someone Hacking into my PC? Please help.
    ... Than an SMC router. ... >> you don't really want sharing. ... > I have a total of three PC's that share the DSL connection. ... I also have a network printer that is hardwired to the router. ...
    (microsoft.public.security)
  • Re: Sharing a Printer
    ... and a Dlink DWL-730AP travel router. ... I'm thinking that if I can fix that problem, the sharing problem will be easy to fix. ... The router has a firewall, but it is set to allow all LAN traffic. ... The following assumes that the PCs on the network are communicating with each other satisfactorily and that the PC to which the printer is connected is powered on. ...
    (microsoft.public.windowsxp.general)