Re: Bosch Panels and numeric pagers

Bosch panels are funny about how they dial out and what they dial out. If you are using a 5200 programmer it is a lot more difficult than using the RPS software (I think 5.9 is the latest version of RPS). I only use RPS so I can't help you with the 5200. The panel can do pager format.
Enhanced Routing
RG4 Pager Yes / No

http://resource.boschsecurity.com/documents/D9412GControlPa_ProgramRecordSheet_enUS_T1659391883.pdf
Enhanced Routing

RG1 Primary SDI Yes / No

RG1 Backup SDI Yes / No

RG1 Pager Yes / No

RG2 Primary SDI Yes / No

RG2 Backup SDI Yes / No

RG2 Pager Yes / No

RG3 Primary SDI Yes / No

RG3 Backup SDI Yes / No

RG3 Pager Yes / No

RG4 Primary SDI Yes / No

RG4 Backup SDI Yes / No

RG4 Pager Yes / No

There are 4 groups for notifications. You'll have to set up the pager notification first and then decide what events you want sent to the pager. Since the panel can report about 400 different events you'll have to check carefully.

Routing Routing Options: Primary (Blank, 1 to 4), Backup (Blank, 1 to 4)

Route 1 Route 2 Route 3 Route 4

Primary Device (Blank) ______________

___

______________

____

______________

____

______________

Backup Device (Blank) ______________ ____

___

______________

____

______________

____

______________

____ View Events Yes / No

Fire Reports Route 1 Route 2 Route 3 Route 4

Fire Alarm Yes / No Yes / No Yes / No Yes / No

Fire Restoral* (After Alarm) Yes / No Yes / No Yes / No Yes / No

Fire Missing Yes / No Yes / No Yes / No Yes / No

Fire Trouble Yes / No Yes / No Yes / No Yes / No

Fire Supervision Yes / No Yes / No Yes / No Yes / No

Fire Restoral* Yes / No Yes / No Yes / No Yes / No

Fire Cancel Yes / No Yes / No Yes / No Yes / No

Fire Supervision Missing Yes / No Yes / No Yes / No Yes / No

Fire Supervision Restoral Yes / No Yes / No Yes / No Yes / No

Burglar Reports

Alarm Report Yes / No Yes / No Yes / No Yes / No

Burg Restore Yes / No Yes / No Yes / No Yes / No

Duress Yes / No Yes / No Yes / No Yes / No

Missing Alarm Yes / No Yes / No Yes / No Yes / No

User Code Tamper Yes / No Yes / No Yes / No Yes / No

Trouble Report** Yes / No Yes / No Yes / No Yes / No

Missing Trouble Yes / No Yes / No Yes / No Yes / No

Non-Fire Supervision Yes / No Yes / No Yes / No Yes / No

Point Bus Fail Yes / No Yes / No Yes / No Yes / No

Point Bus Restoral Yes / No Yes / No Yes / No Yes / No

Non-Fire Cancel Yes / No Yes / No Yes / No Yes / No

Alarm Restore Yes / No Yes / No Yes / No Yes / No

Supervision Missing Yes / No Yes / No Yes / No Yes / No

Unverified Event? Yes / No Yes / No Yes / No Yes / No

Routing Table continued on next page

* Restoral after Trb/Msg/Sup/Bypass. See Fire Supervision Res Event Type prompt in RADXAUX1 for further programming

information.

** Trouble Reports include Point Low Battery conditions from Premises RF Points.

? This event is available only with the D9412G and does not get reported using BFSK format. Additionally, this event will not produce

a corresponding Restoral event.

Heavy outline indicates parameters are available only when View Events is programmed YES.

D9412G/D7412G | Program Record Sheet | EN | 4

9000MAIN Handler Default values are shown in ( ) or in bold

Bosch Security Systems | 4/04 | 47488F

Panel Wide Parameters (continued)

Routing (continued)

User Reports Route 1 Route 2 Route 3 Route 4

Point Bypass/Command Bypass Yes / No Yes / No Yes / No Yes / No

Forced Point Yes / No Yes / No Yes / No Yes / No

Point Opening Yes / No Yes / No Yes / No Yes / No

Point Closing Yes / No Yes / No Yes / No Yes / No

Was Force Armed Yes / No Yes / No Yes / No Yes / No

Fail To Open Yes / No Yes / No Yes / No Yes / No

Fail To Close Yes / No Yes / No Yes / No Yes / No

Extend Close Time Yes / No Yes / No Yes / No Yes / No

Opening Report Yes / No Yes / No Yes / No Yes / No

Forced Close Yes / No Yes / No Yes / No Yes / No

Closing Report Yes / No Yes / No Yes / No Yes / No

Forced Close Perim Instant Yes / No Yes / No Yes / No Yes / No

Forced Close Perim Delay Yes / No Yes / No Yes / No Yes / No

Perimeter Instant Armed Yes / No Yes / No Yes / No Yes / No

Perimeter Delay Armed Yes / No Yes / No Yes / No Yes / No

Send User Text Yes / No Yes / No Yes / No Yes / No

Test Reports

S: Alarm Yes / No Yes / No Yes / No Yes / No

S: Trouble Yes / No Yes / No Yes / No Yes / No

S: Supervision Yes / No Yes / No Yes / No Yes / No

Status Report Yes / No Yes / No Yes / No Yes / No

S: Open Yes / No Yes / No Yes / No Yes / No

S: Close Yes / No Yes / No Yes / No Yes / No

Test Report* Yes / No Yes / No Yes / No Yes / No

S: Perimeter Instant Yes / No Yes / No Yes / No Yes / No

S: Perimeter Delay Yes / No Yes / No Yes / No Yes / No

S: Fire Supervision Yes / No Yes / No Yes / No Yes / No

S: Fire Alarm Yes / No Yes / No Yes / No Yes / No

S: Fire Trouble Yes / No Yes / No Yes / No Yes / No

S: Missing Fire (Trouble) Yes / No Yes / No Yes / No Yes / No

S: Missing Burglary ((Trouble) Yes / No Yes / No Yes / No Yes / No

S: Missing Burglary (Alarm) Yes / No Yes / No Yes / No Yes / No

S: Fire Supervision Missing Yes / No Yes / No Yes / No Yes / No

S: Burglary Supervision Missing Yes / No Yes / No Yes / No Yes / No

S: Door Left Open Yes / No Yes / No Yes / No Yes / No

Routing Table continued on next page

* Please see the D9412G/D7412G Program Entry Guide (P/N: 47775) for additional information on how to generate Off-Normal Test

Reports.

D9412G/D7412G | Program Record Sheet | EN | 5

Default values are shown in ( ) or in bold 9000MAIN Handler

Bosch Security Systems | 4/04 | 47488F

Panel Wide Parameters (continued)

Routing (continued)

Diagnostic Reports Route 1 Route 2 Route 3 Route 4

SDI Device Failure Yes / No Yes / No Yes / No Yes / No

SDI Device Restoral Yes / No Yes / No Yes / No Yes / No

Watchdog Reset Yes / No Yes / No Yes / No Yes / No

Parameter Checksum Fail Yes / No Yes / No Yes / No Yes / No

Reboot Yes / No Yes / No Yes / No Yes / No

Phone Line Fail Yes / No Yes / No Yes / No Yes / No

Phone Line Restoral Yes / No Yes / No Yes / No Yes / No

AC Failure Yes / No Yes / No Yes / No Yes / No

AC Restoral Yes / No Yes / No Yes / No Yes / No

Battery Missing Yes / No Yes / No Yes / No Yes / No

Battery Low Yes / No Yes / No Yes / No Yes / No

Battery Restoral Yes / No Yes / No Yes / No Yes / No

Route Comm Fail Yes / No Yes / No Yes / No Yes / No

Route Comm Restore Yes / No Yes / No Yes / No Yes / No

Checksum Fail Yes / No Yes / No Yes / No Yes / No

Network Fail Yes / No Yes / No Yes / No Yes / No

Network Restoral Yes / No Yes / No Yes / No Yes / No

Network Condition Yes / No Yes / No Yes / No Yes / No

Relay Reports

Sensor Reset Yes / No Yes / No Yes / No Yes / No

Relay Set Yes / No Yes / No Yes / No Yes / No

Relay Reset Yes / No Yes / No Yes / No Yes / No

Auto Function Reports

Sked Executed Yes / No Yes / No Yes / No Yes / No

Sked Changed Yes / No Yes / No Yes / No Yes / No

Fail to Execute Yes / No Yes / No Yes / No Yes / No

RAM Reports

Event Log Threshold Yes / No Yes / No Yes / No Yes / No

Event Log Overflow Yes / No Yes / No Yes / No Yes / No

Parameters Changed Yes / No Yes / No Yes / No Yes / No

RAM Access OK Yes / No Yes / No Yes / No Yes / No

RAM Access Fail Yes / No Yes / No Yes / No Yes / No

Remote Reset Yes / No Yes / No Yes / No Yes / No

Program Access OK Yes / No Yes / No Yes / No Yes / No

Program Access Fail Yes / No Yes / No Yes / No Yes / No

Point Reports

Service Start Yes / No Yes / No Yes / No Yes / No

Service End Yes / No Yes / No Yes / No Yes / No

Fire Walk Start Yes / No Yes / No Yes / No Yes / No

Fire Walk End Yes / No Yes / No Yes / No Yes / No

Walk Test Start Yes / No Yes / No Yes / No Yes / No

Walk Test End Yes / No Yes / No Yes / No Yes / No

Extra Point Yes / No Yes / No Yes / No Yes / No

Send Point Text Yes / No Yes / No Yes / No Yes / No

RF Low Battery Yes / No Yes / No Yes / No Yes / No

RF Low Battery Restore Yes / No Yes / No Yes / No Yes / No

Routing Table continued on next page

D9412G/D7412G | Program Record Sheet | EN | 6

9000MAIN Handler Default values are shown in ( ) or in bold

Bosch Security Systems | 4/04 | 47488F

Panel Wide Parameters (continued)

Routing (continued)

User Change Reports Route 1 Route 2 Route 3 Route 4

Date Changed Yes / No Yes / No Yes / No Yes / No

Time Changed Yes / No Yes / No Yes / No Yes / No

Delete User Yes / No Yes / No Yes / No Yes / No

User Code Change Yes / No Yes / No Yes / No Yes / No

Area Watch Yes / No Yes / No Yes / No Yes / No

Card Assigned Yes / No Yes / No Yes / No Yes / No

Change Level Yes / No Yes / No Yes / No Yes / No

Access Reports

Access Granted Yes / No Yes / No Yes / No Yes / No

Access Denied Yes / No Yes / No Yes / No Yes / No

Door Left Open Yes / No Yes / No Yes / No Yes / No

Cycle Door Yes / No Yes / No Yes / No Yes / No

Door Unlocked Yes / No Yes / No Yes / No Yes / No

Door Secure Yes / No Yes / No Yes / No Yes / No

Door Request Yes / No Yes / No Yes / No Yes / No

Door Locked Yes / No Yes / No Yes / No Yes / No


"Logan" <logan@xxxxxxxx> wrote in message news:Xns9B551F621BAFabc177699@xxxxxxxxxxxxxxxxx
I have a Bosch 9412G panel and I'd like to make it send messages to my
cell's voicemail pager function. The voicemail supports pager mode in
this manner.

Pickup phone
Dial phone number
wait 45 seconds for ringer to time out, message, and instructions
press 5
immediately enter numeric string without
immediately hangup

I tested all this using my regular telephone on the same phone line with
a stopwatch, it works fine that way.

I programmed the panel for 5555551212DDDDDD5, obviously, with the correct
phone number. D represents 7 second pauses, 39-45 seconds is sufficient,
you can press 5 during the instructions, it doesn't mind that. There also
does not need to be a lag between pressing 5 and entering the numeric
string. The voicemail wants, but does not require you to press # at the
end of the numeric string. I tested both the 42 second rule and assertion
that you do not need a delay between 5 and the string, as well as tested
that you can hang up immediately after the string is dumped. All those
things checked out when I tested it using the phone line, the problem I
am having is that the voicemail/pager interface is not reading anything.
At first I thought maybe the leading five was getting lost so I changed
the account number to 5001 so that the leading digit would be five when
it started typing DTMF. I also tried 5555551212ccccccccccccc5 where c is
a 3 second pause for 39 seconds of pause I tested this by answering the
phone early and it seemed to be waiting patiently for that amount of time
and then it dumped the DTMF. Still, when I let it run its course, the
voicemail wasnt receiving it. I even heard it type the 5 to get the pager
access before it started typing the message out when I tested it by
answering. I recognize that using pagers with dialers are so out of
style, but I wanted to use it as a corollary to monitoring service.
Anyone here set this up before on any panel? Any thoughts on this?

thanks,
Logan

.

Relevant Pages

  • Re: Bosch Panels and numeric pagers
    ... programming "sheet" ...jeez. ... The panel can do pager format. ... Enhanced Routing ... RG1 Primary SDI Yes / No ...
    (alt.security.alarms)
  • Re: DSC Power 632 DIY questions
    ... The PC1555MX (AKA Power 632) seems to have the same programming as the ... The toughest one is getting panel feedback. ... If you leave this field as "FF" when you've activated the "Pager" option, the panel won't transmit anything. ...
    (alt.security.alarms)
  • Re: DSC Power 632 DIY questions
    ... is your communicator enabled? ... .Make sure your panel time is set ... RTFM especially 5.9 Pager Format: ...
    (alt.security.alarms)
  • Re: Bosch Panels and numeric pagers
    ... I think they do just dump if going to a pager (if panel is capable of ... pager...the panel never really knows if it got through. ... there is no receiver answering the panel's attempt at communication. ... start to dial DTMF and I could recognize the leading digit 5 when it ...
    (alt.security.alarms)
  • Re: Bosch Panels and numeric pagers
    ... programmed right (or the panel isn't pager capable) and it's sitting ... Each pause is equal to about three seconds. ... counting down the time delay OR it starts the time delay at some other ...
    (alt.security.alarms)