Re: Ademco Vista 20 X10 programming question
- From: "Mark Leuck" <m..leuck@xxxxxxxxx>
- Date: Mon, 3 Dec 2007 22:12:19 -0600
That will be real helpful to someone with a fixed english keypad
"Robert L Bass" <RobertLBass@xxxxxxxxxxx> wrote in message
news:kBV4j.22219$AX6.7349@xxxxxxxxxxx
"Bob Sisson" <inspectionsbybob@xxxxxxxxxxx> wrote in message
news:IIadnR0BCqNsBczanZ2dnUVZ_jqdnZ2d@xxxxxxxxxxxxxx
Compass will do X10 Coding ?
OK...I have compas, or can get it (my is an older version)
Do I need that weird modem still? (I still have a Hayse 1200b just
for my alarm panel)
Programming X-10
1. Enter program mode by powering down then back up & pressing the
*+#
simultaneously within 50 seconds of power up, or enter the Installer
code (4112)
+ 8 + 0 + 0.
2. Screen displays, "INSTALLER CODE 20"
3. Press "*" 27, screen displays "X10 HOUSE CODE 27" enter the
desired X-10
House Code. 0=A, 1=B, 2=C, 3=D, 4=E, 5=E, 6=G, 7=H, 8=I, 9=J, #+10=K,
#11=L, #12=M, #13=N, #14=O, #15 =P.
4. Press "*" 79, screen displays:
Enter Output No.
(00 = Quit) 01
Enter the Device Number 01-18 for Powerline Carrier devices; or 00 to
end
these entries. Press ? to continue.
5. Screen displays:
01 Output Type
Delete 0
Enter 2 for X-10
Press ? to continue.
6. Screen displays:
01 Unit No.
01
Enter the Unit Number for the X-10 device, 01-15
Press ? to continue.
7. Screen displays:
01 Enter Output No.
(00 = Quit) 02
Enter 00 to quit or refer back to step 4.
8. Screen displays:
Enter ? or #
Press ?or # to exit
9. Enter " 80 "
Screen Displays:
Output Funct #
(00 = Quit) 01
Enter X-10 programming 01-48. Press ? to continue.
10. Screen displays:
01 A E P Trig
?00 0 0 - ZL=00
This is the summary screen, 01=Device #, A=Device Action;
E=Triggering
Event; P=Partition; Trig=Trigger Type; Press ? to continue.
11. Screen displays:
01 Activated By:
Delete 0
Enter the initiating event for this output device:
1=Zone List (See Step 12)
2=Zone Type (See Step 13)
3=Zone Number (See Step 14)
Press ? to continue.
12. Screen displays:
01 Zn List
None 0
If a zone list will be used enter the number to be used (01-08);
NOTE: 9-12 are
used for pagers.
Press ? to continue.
12a. Screen Displays:
Enter Event
Restore 0
Enter the zone list event that will activate this output:
0=Restore; 1=Alarm; 2=Fault; 3=Trouble
Press ? to continue, See Step 15 for next program location.
13. Screen displays:
01 Enter Zn Type
Zone Disabled 00
Enter the desired zone type, Press ? to continue.
13a. Choices for Zone Types:
00=Not Used
01=Ent/Exit #1
02=Ent/Exit #2
03=Perimeter
04=Interior Follower
05=Trouble Day/Alarm Night
06=24 Hr Silent
07=24 Hr Audible
08=24 Hr Aux
09=Fire
10=Inter w/Delay
12=Monitor Zone
14=Carbon Monoxide
16=Fire W/Verification
23=No Alarm Response
24=Silent Burglary
25=24 Hr Non-Alarm
77=Keyswitch Zone
13b. Choices for System
Operation:
20=Arming Stay
21=Arming Away
22=Disarming
31=End of Exit Time
32=Start of Entry Time
33=Any Burg Alarm
36=**Bell Timeout***
38=Chime
39=Any Fire Alarm
40=Bypassing
41=**AC Power Failure
42=**System Bat Low
43=Comm. Failure
52=Kissoff
54=Fire Zone Reset
**Use 0 for Part # (P)
58=Duress
60=AAV
66=Function key ?
67=Bell Fail
68=Telco Line Cut
78=Keyswitch Red LED
79=Keyswitch Grn LED
***Or at disarming
?Use *57 to assign (07)
13c. Screen displays:
01 Partition
Any Partition 0
Enter the partition in which this zone type will occur: 0=Any
partition;
1=Partition 1; 2=Partition 2; 3=Common, Press ? to continue, see step
15 for
next program location.
14. Screen Displays:
01 Enter Zn Num.
None 00
Enter the zone number associated with this output number, Press ? to
continue.
14a. Screen Displays:
01 Enter Event
Restore 0
Enter the zone event that will activate this output: 0=Restore;
1=Alarm/Fault/Trouble
Press ? to continue.
15. Screen Displays:
01 Output Action
Off 0
Enter the desired device action as listed below, Press ? to continue.
0=Off
1=Close for 2 Seconds
2=Close & Stay Closed
3=Continuous Pulse on & off
4=Toggle State of Relay
5=Duration 1 (see field 1*77)
6=Duration 2 (see field 1*77)
16. Screen Displays:
Enter Output No.
?00 00
Enter the device output number (programmed in *79 menu mode) you want
associated with this output, Press ? to continue
17. Screen Displays:
01 A E P Trig
X01 0 0 - Zn=02
Press ? to continue
18. Screen Displays:
Output Funct #
(00 = Quit) 02
If programming is complete enter 00 to quit, otherwise refer to step
9
19. Screen Displays:
Enter ? or #
Enter ? or # to exit
20. Screen Displays:
Field?
Press 99 to exit program mode
--
Regards,
Robert L Bass
==============================>
Bass Home Electronics
4883 Fallcrest Circle
Sarasota · Florida · 34233
http://www.bassburglaralarms.com
Sales & Tech Support 941-925-8650
Customer Service 941-232-0791
Fax 941-870-3252
==============================>
.
- References:
- Re: Ademco Vista 20 X10 programming question
- From: Bob Sisson
- Re: Ademco Vista 20 X10 programming question
- From: Robert L Bass
- Re: Ademco Vista 20 X10 programming question
- Prev by Date: Re: Uplink Network/Line costs?
- Next by Date: Re: Ademco Vista 20 X10 programming question
- Previous by thread: Re: Ademco Vista 20 X10 programming question
- Next by thread: It never fails
- Index(es):
Relevant Pages
|
