Re: Napco MA3000 - Dialer Test on both Lines?


"Rube Goldburg" <robberbass@xxxxxxxxxxx> wrote in message
news:0LGdnYfFr49odl_ZnZ2dnUVZ_v6dnZ2d@xxxxxxxxxxxxxx
Ok. Two programmable relays are set to interrupt a 24-hour test zone and
to short phone line 1 at the designated time. This causes the panel to
report the 24-hour zone as a silent alarm, but the code/zone is configured
at the c-station to be viewed as a test signal.

assuming [ you know what that means] that there is a "spare" zone on the
panel.

Seeing as you ar not qualified to actuyally do this I find it interesting
that you would suggest this to some unsuspecting diyer just to get them to
buy parts.
And if the building burns down and the diyer is in court and the attorney
ask why would you install a system that doesn't have the capability to send
test signal on both lines as required by code? And you changed the SIA or
CID codes at the Central Station to pull the wool over the AHJ eyes and get
your system passed when it obviously doesn't meet code? Where did a diyer
come up with this rube goldberg design? Where will bass be? Obviosly no
licensed fire alarm installer would do something like this. This must be
why FL is changing the regs to stop unlicensed parts clerks from giving
advise on system design.

A third relay can be triggered by "general trouble" and run in series with
the phone shorting relay so that line 1 will not short out if the panel is
currently experiencing a trouble condition.

Here's an interesting thing about the MA3000 when used with the 2-line
dialer board. If either line develops a trouble condition during a
reportable event the panel will only display and attempt to report the
trouble after finishing the original report. What happened with this
sequence was the panel would report the 24-hour zone and the line would
immediately restore.

notice how when shown the error of his ways he starts adding more relays and
changing his rube goldburg design. This is a classic bassanova. By the end
of this thread bass MAY actually have this figured out, with hints and ideas
to point him in the right direction from people who actually do this for a
living and then will pretend this was his idea all along. and the only
reason we doubted him in the first place was because some unknown persons
supposedly don't like DIY. How long before this turns up on one of his
sites as another gem of knowledge from the brain of the robber bAss.


.

Relevant Pages

  • Re: WTO Ruling WT/DS285/RW Measures Affecting the Cross-Border Supply of Gambling and Betting Se
    ... UNITED STATES - MEASURES AFFECTING THE ... Report of the Panel ... Specific findings and conclusions in the original proceeding 16 ... REFERRED TO IN THIS REPORT ...
    (rec.gambling.poker)
  • Re: ISE software bug???
    ... The design & report files attached below. ... TIMING REPORT ... Add Generic Clock Buffer: 8 ...
    (comp.arch.fpga)
  • Re: Date range on reports
    ... box to your report with a control source like: ... > In the Database window (Database window: The window that appears when you ... > In the New Form dialog box, click Design View, and click OK. ... > Begin by clicking Macro Names to display the Macro Name column. ...
    (microsoft.public.access.reports)
  • Re: Date range on reports
    ... Create an unbound form (unbound form or report: A form or report that isn't ... In the Database window (Database window: The window that appears when you ... In the New Form dialog box, click Design View, and click OK. ... Begin by clicking Macro Names to display the Macro Name column. ...
    (microsoft.public.access.reports)
  • RE: Multiply qty of filtered records
    ... If you should want to try doing this with a query (which is probably the more ... etc in the bottom part of the design view. ... I do know how to get this information in a Report, ... Dim rs As DAO.Recordset ...
    (microsoft.public.access.modulesdaovba)