Re: WEP and MAC Filter

bnmohan via HWKB.com wrote:
<My Linksys WRT54Gv2 does it right: the WPA (or WEP) key must match AND the
<MAC address must match (if Permit Only is selected) for the PC to access
<the 'net.
<
<Sounds like the DIR-300 has a bug or (just maybe) you did not correctly
<set up the MAC filter; double-check your settings.
<
< Signature
<
<
<Cheers, Bob

Could it be because the DHCP server is enabled, and the incoming wireless
adaptors were on get dynamic IP when I try to connect them to the router?
I am not sure of the sequence to be followed: I set the wifi adaptor IP to my
local lan; remove 802/11b authentication, connect to the router. I am never
sure in what order I do the three. It ends up at 'validating identity' most
of the time. Sometimes it connects; but the lan is not available ( because
the router is on one subnet and the lan on another). I go to the router and
enter the MAC address. When I retry, it still fails, and I find the 802/11b
auth has come back, or the new IP is gone :-(. I remove the auth, put back
the IP, and the thing connects. I am not sure if the 802 auth had come back
earlier, and the connection would have been made if the auth was removed,
without entering the MAC on the router.

Sorry, all that appears quite incoherent even to me!

Mohan
I would be happy if someone could point out the correct sequence to be
followed.


From your confusing description, I can't tell how you have connected the
router into your environment. For a normal SOHO application, the WAN port
would be cabled to the cable/DSL modem, the 1-4 wired PCs would be
cabled to the 1-4 LAN ports, and the wireless PCs would be channeled
via 802.11G/802.11B to the radio end of the router; normally, all wired
and wireless PCs would be on the same LAN subnet, and all would access to
the 'net via the router's WAN port. Is this what you have, or want?

I don't know what you mean by "802/11b authentication". 802.11B is a
protocol and signalling mechanism used by some wireless nodes, just as
is 802.11G. Neither 802.11B nor 802.11G specify authentication. FWIW,
if all of your PCs are new enough to support 802.11G, I suggest disabling
802.11B in the router, since pure 802.11G will give better performance.

To simplify your LAN while troubleshooting, I suggest not using MAC filtering.
After everything works, you can turn MAC filtering ON and ALLOW only those
PCs that you want to access your LAN (and/or your pipe to the WAN). Note
that MAC filtering offers rather limited security, and probably is not
worth the effort. To secure the wireless segment of your LAN, use WPA2
or WPA or (at least) WEP; pick the best (WPA2 if possible) method that all
of your wireless PCs can use. For a new network, I suggest getting it
all working without wireless encryption, then turning on encryption in the
router and one wireless PC, then in each other wireless PC; it is easy to
screw up when trying to enter the same passphrase into the router and the
PCs, so do it one PC at a time and expect to do it over a few times (until
the difference between password and passphrase becomes clear).

As for DHCP, I would use it across the board from day one. It is very easy
to set up, in the router and in wired and wireless PCs, and it is pretty
robust. If you have problems and want to experiment, you can use DHCP on
some PCs but not others: with the DHCP server set to its normal range of
192.168.0.x (100 < x < 150), you can manually enter an IPA which is in the
same subnet but outside of the DHCP range (e.g., IPA=192.168.0.55 with a
mask of 255.255.255.0); how you assign that IPA to a PC depends on the
OS and the specific device driver for that PC.
--
Cheers, Bob
.

Relevant Pages

  • Re: How do I fix the problem of duplicate IP address ?
    ... He helped the way our network is set up. ... 'Wireless' systems, neither do we. ... It is serving the rest of our PCs ... Your wireless router must have DHCP running and is issuing IP ...
    (microsoft.public.windowsxp.network_web)
  • Re: weird weird weird Linksys router
    ... Normally, when this happens, resetting the modem and router ... That fixed it (and my connection was way zippier than normal); ... including cloning its MAC Address to the same as my G4's MAC ... In my case it loses wireless connectivity ...
    (comp.sys.mac.comm)
  • Re: How do I fix the problem of duplicate IP address ?
    ... > He helped the way our network is set up. ... > 'Wireless' systems, neither do we. ... It is serving the rest of our PCs ... Your wireless router must have DHCP running and is issuing IP ...
    (microsoft.public.windowsxp.network_web)
  • RE: Wireless access
    ... authorized WLAN cards on the wireless router. ... change your MAC address (and effectively spoof the MAC address of another ... address of other cards connecting with the WLAN router. ...
    (Security-Basics)
  • Re: How do I fix the problem of duplicate IP address ?
    ... I am glad it is working again but John is correct that your network topology ... Your wireless router must have DHCP running and is issuing IP ... DHCP server and is issuing IPs to any PCs linked through it. ...
    (microsoft.public.windowsxp.network_web)