Re: AC thermostat malfunction

On Dec 8, 7:11 am, "RBM" <r...@xxxxxxxxxxx> wrote:
"MiamiCuse" <nmbexc...@xxxxxxxxxxx> wrote in message

news:r5SdndH62uJJ56HUnZ2dnUVZ_tHinZ2d@xxxxxxxxxxx







"Oren" <O...@xxxxxxxxx> wrote in message
news:sqroj49ep2s31idop66pvssk6hv4h6lvkt@xxxxxxxxxx
On Sun, 7 Dec 2008 18:25:42 -0500, "MiamiCuse" <nmbexc...@xxxxxxxxxxx>
wrote:

I have the old style thermostat on my AC that is giving me some trouble.
I
have played with it a bit and have isolated the problem to the point I
think
may be someone can tell me if it can be fixed or have to get a new one..

It is the old style with a mercury bulb inside, the manually adjust a
dial
to the desired temperature.  There are two switches:

- fan ON or AUTO swicth - I leave it on AUTO
- HEAT OFF COLD switch

Down here in Miami, I pretty much leave the HEAT OFF COLD on COLD.  I set
it
to 72 degrees and that works fine.  If it dips below 72 the AC kicks on.

Last two weeks we had a cold front so I turned on the heat, I might use
the
heat once every two year or so, last may be a week here, a week there.

If I set it on HEAT the heat does not kick on no matter how I adjust the
temperature settings.

I then removed the cover, and adjust the settings left and right and I
can
see the mercury drop rock left and right.

However, if I set the switch from HEAT to OFF, wait 2 seconds, then set
it
back to HEAT, if I then adjust the temperature setting I can see the
mercury
drop moved to one side and when it hits the wire filaments inside a very
faint spark, and the heat comes on.  It stays on until the temperature is
reached then it goes off.  It will stay off from now on unless I turn the
switch to OFF and back to HEAT, and adjust the temperature then it will
come
on again.

Any ideas what is wrong?

Thanks for any comments.

MC

Replace the T-stat with digital. Save the mercury and poor into
drilled out bullets.

Is it easy to wire in a new thermostat?  Do I just pull it off and the new
one will match up to the existing wiring?

You first have to identify what type of thermostat you have, which you can
do pretty much by identifying the letter terminals that are on its base.
Once you know what you have, you get a new stat with the same or more
lettered terminals that it has. When I replace thermostats, I leave the
existing unit attached to the cable(s), and with power to the
heating/cooling systems off, I cut the cable(s) close to the stat, then
mount the new unit and wire it terminal for terminal by looking at the old
unit



- Hide quoted text -

- Show quoted text -- Hide quoted text -

- Show quoted text -


It's hard to imagine a simple old mercury thermostat behaving the way
that is described. If it turns on and correctly works each time it's
moved from off to heat, but then doesn't work a second time, I can't
conceive of a problem with the thermostat that would make it behave
that way.
.

Relevant Pages

  • Re: HVAC Heat Pump Question
    ... This morning it was 36 outside, the actual temperature ... registered on the theromastat was 68 and the aux heat was on. ... When there is a outdoor thermostat ...
    (alt.home.repair)
  • Re: Programmable or standard thermostat ?
    ... not having kept the temperature 15 degrees higher. ... costs to heat. ... Of course if you manually move your thermostat each time you ... you'd be waking up/coming home to a colder house. ...
    (alt.home.repair)
  • Re: 2001 SL2 - low temp indicated and very little heat
    ... heat but it doesn't. ... slide the temperature warmer>>> Can't seem to get it to warm up ... broken or the thermostat is stuck open. ... flush to get rid of the sticky gunk that had shown up in the coolant ...
    (rec.autos.makers.saturn)
  • Re: AC thermostat malfunction
    ... to the desired temperature. ... heat once every two year or so, last may be a week here, a week there. ... You first have to identify what type of thermostat you have, ... do pretty much by identifying the letter terminals that are on its base. ...
    (alt.home.repair)
  • Re: AC thermostat malfunction
    ... to the desired temperature. ... I pretty much leave the HEAT OFF COLD on COLD. ... If I set it on HEAT the heat does not kick on no matter how I adjust the ... do pretty much by identifying the letter terminals that are on its base. ...
    (alt.home.repair)
Loading