Re: Can I put a coffee warmer on a dimmer switch?

On Sep 19, 8:16 am, "JohnR66" <nos...@xxxxxxx> wrote:
"John Grabowski" <jgrabo...@xxxxxxxxxxxxx> wrote in message

news:48d37e46$0$4901$607ed4bc@xxxxxxxxx





"Square Peg" <Square...@xxxxxxxxxx> wrote in message
news:lqb6d4hsbhai3h45j5ko5uk7r5a4t1rujb@xxxxxxxxxx
Most coffee mug warmers are under-powered. One reviewer on Amazon said
that they were restricted to about 24 watts by law.

This one

http://www.amazon.com/Bunn-BCW-Warmer-Home-Decanters/dp/B00023WAS0/re....

is made for warming the whole coffee pot. It says it's 120V/15amp.
Several of the reviews say that they use it for a single cup, but it
keeps it too hot. It only has on/off -- no temperature control.

Can I put it on a 300 watt dimmer switch like this?

http://www.amazon.com/Lutron-Electronics-Plug-Dimmer-TT-300H-WH/dp/B0....

If not, is there a way to ramp the the power down as an external
thermostat?

You will probably be disappointed in the results and waste electricity at
the same time.  The heating elements are designed to perform at a certain
voltage.  As that decreases so will the heat level, but it will not be on
a straight line but rather a drastic curve due to the resistive nature of
the elements.

Take a look at what happens when a light bulb is dimmed.  Not only is the
light output diminished, but the color of the light changes as well
because they were designed for certain voltage.

An incandescent light bulb is inefficient at producing light and it gets
much worse as the voltage is reduced, however, it is great at producing
heat.
If you reduce the voltage on a heating element, it will produce less heat
but is still nearly 100% efficient at producing the heat. It does not become
less efficient if that is what you were trying to say.- Hide quoted text -

- Show quoted text -

A resistance element in a heater like this behaves a lot differently
than a light bulb. The temperature change in a lightbulb goes from
room temp when off to thousands of degrees when lit. That causes the
resistance of the filament to change substantially from cold to
hot. In the case of a resistance heater in a coffee pot, the
resistance of the element is going to change much over the small
temperature range from 70 to 150 or so degrees.
.

Relevant Pages

  • Re: Homemade Resistance Soldering Unit
    ... Tricky measuring either voltage or current due to the magnitude of values and the way the tip changes resistance with heat. ... I'm sorry, I not sure what you were referring to that is not DC output, unless it is the resistance welder and not the charger. ... Gunner has mentioned soldering heavy wires by pressing a 250-watt gun ... I recently measured the voltage across the tip of my 250-watt Wen soldering gun - it's 0.175 volts rms or so. ...
    (rec.crafts.metalworking)
  • Re: My Stove
    ... A low resistance means that there is more ... > potential to generate heat rapidly and heat the element. ... end where it plugs into the heating element to the end where it plugs ... > turned the variable control on, and the voltage at low heat registered ...
    (sci.electronics.basics)
  • Re: Can I put a coffee warmer on a dimmer switch?
    ... that they were restricted to about 24 watts by law. ... As that decreases so will the heat level, but it will not be on ... because they were designed for certain voltage. ... An incandescent light bulb is inefficient at producing light and it gets ...
    (alt.home.repair)
  • Re: Can I put a coffee warmer on a dimmer switch?
    ... that they were restricted to about 24 watts by law. ... As that decreases so will the heat level, but it will not be on ... because they were designed for certain voltage. ... An incandescent light bulb is inefficient at producing light and it gets ...
    (alt.home.repair)
  • Re: Can I put a coffee warmer on a dimmer switch?
    ... The heating elements are designed to perform at a certain voltage. ... As that decreases so will the heat level, but it will not be on a straight line but rather a drastic curve due to the resistive nature of the elements. ... It seems to me that with less voltage, fewer photons will ... Your analysis is correct as far as it goes, but you need to recognize that the resistance is not a constant. ...
    (alt.home.repair)