Re: Why no headphone jack on tube amps?

On 28 Jun 2007, "David Martel" <marte005@xxxxxxxxxxxxx> wrote in
alt.guitar.beginner:

Snark,

Using a power soak, I call it a dummy load,

Ya, I think "Power Soak" was a brand name (still?). I had one about
25 years ago, but yes, essentially it is a dummy load.

Some one posted about a Peavey amp with a headphone feature but
complained that the tone was poor. I suspect that losing the
speakers' contribution to the tone will require some sort of
dedicated EQ circuit for the headphones.

Dave M.

Well, it's not just freq response (which is what EQ can adjust for),
but that the speaker's physical characteriscs and motion colours the
sound (both in the air, and to some effect this gets reflected back
into the final stage of the amp). Obviously any reflected
"electronic influence" also to some extent flavours your power amp
distortion and sound qualities.

But at the end of the day, what you have to determine is whether it
is "good enough". At this level you'll have many people in
disagreement over what is good enough. But your opinion is the only
one that counts here. ;-)

First and foremost is the safety of the finals in the amp (a
suitable load). Second is the sound level in your earphone jack.

The best way to settle it for yourself is to simply borrow a dummy
load, and wire up an external jack arrangement (get 3 jacks and just
wire it up without a box). This will give you the power level you
want in your earphones by suitable choices of resistor. Just watch
out for the power level of your resistors (5 to 10W should be plenty
good for earphones, assuming a good choice of resistance values
used).

Then if you like it, you can house that in a little box. Have 1
speaker input jack, a dummy load jack and a earphone jack. If you
want to get fancy you can add a monitor jack for recording purposes
(again, some suggest this ain't good enough for recording, but I beg
to differ, until I try it for myself ;-)

Snark.

--
Posted via a free Usenet account from http://www.teranews.com

.

Relevant Pages

  • Re: Why no headphone jack on tube amps?
    ... I think "Power Soak" was a brand name. ... I had one about 25 years ago, but yes, essentially it is a dummy load. ... The best way to settle it for yourself is to simply borrow a dummy load, and wire up an external jack arrangement. ... a dummy load jack and a earphone jack. ...
    (alt.guitar.beginner)
  • Re: Why no headphone jack on tube amps?
    ... I think "Power Soak" was a brand name. ... Well, it's not just freq response, but that the speaker's physical characteriscs and motion colours the sound (both in the air, and to some effect this gets reflected back into the final stage of the amp). ... The best way to settle it for yourself is to simply borrow a dummy load, and wire up an external jack arrangement. ...
    (alt.guitar.beginner)
  • Re: HP Pavilion Laptop Owners with Bad Power Jacks....
    ... jack dilemma. ... I purchased a HP laptop to keep all HP software off my other systems. ... power jack and are not HP laptops. ... Like many others I assumed the battery had failed ...
    (comp.sys.hp.hardware)
  • Re: Why no headphone jack on tube amps?
    ... Using a power soak, I call it a dummy load, ... I think "Power Soak" was a brand name. ... reflected back into the final stage of the amp). ... level you want in your earphones by suitable choices of resistor. ...
    (alt.guitar.beginner)
  • Re: Inexpensive fairly good quality home brew or kit RF power meter
    ... One of the kits on the page I referenced could be the basis for his power ... A simpler way would be to read the peak voltage across the load. ... dummy load that should cover the frequencies of interest. ... parallel for a 200 watt 50 ohm dummy load. ...
    (sci.electronics.repair)
Loading