Re: Fluke 8600A -- a new question about calibration

On Sun, 05 Oct 2008 16:17:30 -0400, Rich Koerner <richk@xxxxxxxxxxxxx>
wrote:



"Phil S." wrote:



<snip>




Phil, every bargain has its price.

Of course it does! I was bargain hunting!


A calabrated piece of gear has its value.


IMO, moreso to a pro tech than a casual user. Still, I agree with this.

Keep subtracting the probe resistance, and stay with the Tripplett?


No, that Tripplett has other issues, as well. I've been hankering for
something better. It will make a nice backup meter from this point forward.
Also, it measures capacitance, and, while probably not extremely accurate,
give me a decent idea of whether a cap should be tossed out, but this
diverges from the topic.

With my 8600A, I always have to account for the probe resistance in the
low range.

This is precisely my question.

Circuit contact points have to be made correctly, and the meter side plugs
have to be spun around a few times to
insure good contact.


OK, that's not in the manual <grin> and why I'm asking. I might have
figured this out and might not have.

THAT, goes with territory with any meter used in the very low resistance
ranges.

Uh, huh, I can live with that. Like I said, where should I set my
expectations? This is the answer.


When I got my 8600A, it had been cal'd, and the probes when shorted would
read zero. A few days
later, it would read .1. Twist the plug ends in the meter, and its back
to zero again.

Clip leads to the chassis from the meter ground side in low resistance
measurements are never good
practice in low resistance measurements. Very hard and extremely sharp
probe tips on the contact
side is the only way to make good probe surface contact in the low
resistance measurment game.

Your measurement technique becomes very important, even when you have the
best set of probes.


I've noticed this. There are times when it is hard to get a meter to
stabilize. Without a mentor present to show me, I've been guessing what I
should do. Believe it or not, these words are very helpful.

When you pinch the leads of a resistor to the ends of the meter probes,
did you scrape down the
resistor leads to get all the oxide off for good meter contact?


I'll plead the 5th amendment here.


Check yourself out.




http://wiringstuff.com/images/Picture%20029.jpg

I use these.

Take an Arkansaw stone
http://www.sharpeningsupplies.com/Oil-Stones-C5.aspx?gclid=CLKZ7qfvkJYCFQOcFQod9n45EQ and run it
over the sides to sharpen the edges.

Then, hold the component body between your fingers. Place the pliers on the lead at the body,
squeeze, and slide the pliers over the lead to the till it slips of the ends.

Works like a dream.







I think you just did! Thanks again.

BTW, I'm in the middle of the battery replacement job. It is a PITA to
thread those leads and screw together the battery retainers. I've got one
screwed to the board, but only two of the 4 black plastic feet actually
seated properly in the holes. When I saw this, I thought I'd sleep on it.
After a decent night's sleep, I see the wisdom in pulling it off and making
it exactly as it should be and not just settling for "almost". It's one of
those jobs that would go much faster with 3 or 4 hands attached to one
brain.


Take your time, and be precise with your work.




Regards,

Rich Koerner,
Time Electronics.
www.timeelect.com

Specialists in Live Sound FOH Engineering,
Music & Studio Production,
Vintage Instruments, and Tube Amplifiers
Little piece of emory cloth works good also..good for soldering
leads..
.

Relevant Pages

  • Re: Fluke 8600A -- a new question about calibration
    ... It will make a nice backup meter from this point forward. ... Clip leads to the chassis from the meter ground side in low resistance ... practice in low resistance measurements. ...
    (alt.guitar.amps)
  • Re: Digital meter feedback?
    ... It requires a 5VDC power supply. ... I am using the meter with a 13.8V system. ... Without the shunt leads ... As soon as the shunt leads are ...
    (sci.electronics.basics)
  • Re: electronics help
    ... and the other VOM lead to the neg/empty 1/2 of the battery clip? ... But the multimeter in-line with the battery. ... Then start wiggling the leads that attach to the jacks and the circuit ... in ammeter mode vs ohmmeter or volt meter modes. ...
    (alt.guitar.bass)
  • Re: Digital meter feedback?
    ... It requires a 5VDC power supply. ... I am using the meter with a 13.8V system. ... Without the shunt leads ... there is an unnecessary and undesirable connection between ...
    (sci.electronics.basics)