Re: Shock Info

teemukyttala@xxxxxxxxx wrote:
I don't even know why people ask questions like:


how long does it take that bleed-resistor to make the circuit
safe.....and can this be used on any tube amp?


You are asking for an information that can be found from every
respected book about electronics theory! I do hope that people take
time to do old-fashioned stuff like reading books or studying BASIC
electronics before they decide that they are competent enough to start
dealing with potentially LETHAL tube circuits. To answer the question:
The resistance is not the only variable in the related theory. You
need to calculate the time constant t and how long it is (in seconds)
from:

t = R C,

where C = the capacitance storing a specific charge and R = resistance
that shunts the capacitor to ground.

During the first time constant, voltage drops to 36,8% of the initial
value. Basically, the voltage drops according to following table:

1t = 36,8 % of initial value
2t = 13,5 % of initial value
3t = 5% of initial value
4t = 1,8 % of initial value
5t = 0,7 % of initial value

So you see, the voltage and capacitance are equally important as the
resistance of the "bleeder" resistor. This should give a rough
estimate of the time it takes for the capacitor to discharge to a
"safe level" - whatever that is. However, in practice you don't count
seconds but MEASURE the voltage with multimeter before you touch
anything with anything other than the measurement probes! The "bleeder
resistor" discharge method works with all electric appliances that
store charge to capacitors - and that definition includes tube amps.


And although the famous "screwdriver method" will provide a nice spark
show don't use it because:
1. Dielectric absorption may become a problem with high voltage
charges
2. You have a risk of ruining the capacitor since during the discharge
the only current limiting factor is ESR
3. You have even higher risk of destroying delicate solid-state
devices that the circuit might contain
4. You ruin the screwdriver

I asked it so that the question would get out and an explanation (of sorts) would be provided. Sometimes 'loaded questions' get asked to do just that.

Telling folks to do research is a great idea; how many will do it? This is a safety issue, I think, and background information is appreciated; denigrating anyone for asking questions doesn't help anyone.

This is not alt.guitar.amps.experts.only. There are some folks here who would have everyone "go to school" for every answer found in "any respected book about electronics theory". Do you suppose that the previous poster who mentioned installing such resistors on B+ used your table?

Sorry for the long (and possibly petulant) response, and by the way, thanks for the information.
.

Relevant Pages

  • Re: Simple capacitor circuit (slowly illuminating LED)
    ... >> across the capacitor is proportional to the charge it contains and second ... I took my multimeter and measured the voltage ... I left the circuit closed for two hours just to see if it ... > Now, at their lowest, the resistance of the capacitor and ...
    (sci.electronics.basics)
  • Re: Shock Info
    ... safe.....and can this be used on any tube amp? ... The resistance is not the only variable in the related theory. ... that shunts the capacitor to ground. ... During the first time constant, voltage drops to 36,8% of the initial ...
    (alt.guitar.amps)
  • Re: My NE-2 Relaxation Oscillator is Too Relaxed ???
    ... the capacitor is a 1uF electrolytic rated at 160V. ... don't have any capacitors on hand with a higher working voltage. ... I can get the bulb to blink around 3 times ... Lowering the resistance makes the bulb turn on continuously. ...
    (sci.electronics.basics)
  • Re: Absolute Beginner--Making Sense Of Capacitors
    ... Current caused by a given voltage difference is inverse to the resistance of any path. ... This proportionality is captured in Ohm's law. ... It states that the current is proportional to the voltage and inverse to the resistance. ... A better way to say this is that the current through a capacitor is proportional to both the capacitance and the rate of change of voltage across it. ...
    (sci.electronics.basics)
  • Re: Shock Info
    ... electronics before they decide that they are competent enough to start ... The resistance is not the only variable in the related theory. ... that shunts the capacitor to ground. ... During the first time constant, voltage drops to 36,8% of the initial ...
    (alt.guitar.amps)