Re: Music Man HD130 tube problems

In article <1146933149.780923.112750@xxxxxxxxxxxxxxxxxxxxxxxxxxxx>,
kremer307@xxxxxxxxx wrote:

So, to finally answer these questions, the chassis number of the amp is
2275-130, and the diagram on the inside calls for 4 6CA7's. I was
unable to find a bad connection or resistor around the tube socket, but
I didn't look too thoroughly, because I'm still planning on taking the
amp in.

Check the value on the two large 1.5K/10W resistors. One may have
overheated. This wouldn't be a *cause* of a loss of bias, but could be
a result of a shorted tube.

Also, there's a small fiberboard adjacent to the tube sockets with some
resistors and caps. If one of those caps is leaky, or open resistors,
or cracked solder, you've lost bias to two tubes.
Touch up all the solder joints on this small board (MAKE SURE THE AMP IS
DISCHARGED).

Unless you can remove the caps and do a leakage test, you'll have to
measure voltages while the amp is energized to see if they're leaky.
This amp works at 700VDC. Needless to say, BIG DANGER!!!! This job is
best left to a pro. Look to see if there are any signs of arcing
between pins 2 and 3 on any of the output tube sockets (on the solder
side of the socket).

So, to confirm a couple of things with you all, I'm better off leaving
the cabinet wired at 3.6 ohms and using the 4 ohms setting, or wiring
it back up to 16 ohms? Seems like 3.6 ohms is the best bet, but it's
still 10% under the expected load. Not enough to worry about? Would
finding a totally new 8 ohm cabinet to use be far superior to using the
3.6 ohm (or 16 ohm if I wire it up again) cabinet I've got now?

<nitpicking>
3.6 ohms is actually the DC resistance, not the impedance. Because
impedance is the vector sum of inductive reactance (a
frequency-dependent AC property not measured wihh your ohmmeter) and
resistance, impedance is always more than resistance. Usually something
like a factor of 1.4 more or less. 3.6 ohm resistance would be
considered a nominal 4 ohm impedance.
</nitpicking>

DON'T run this amp at 16 ohms!!!! 8 ohms is probably a little more
robust than 4 since you're using the entire secondary of the OPT, and
not half of it, but it really should run OK at 4 ohms with the correct
toggle setting. 4 new speakers will set you back nearly $300...more
than the cost of replacing your output tranny. Is this worth it to you?

And I should look for some high-pot tested electroharmonix 6CA7's if
I'm not planning on hunting down the original sylvanias? These EH's
seemed to be the favorite throughout the post.

Yeah, they work. I'm skeptical if *any* vendors routinely match these
tubes at the high voltages of a Music Man. I'm not sure if you'll see
any difference between a normal matched pair and one which is "hi pot"
tested. FWIW, most vendors will match at around 450VDC. Some vendors
spot-check batches for high voltages, but not routinely. New Sensor, the
main distributor of ElectroHarmonix and Sovtek, matches at only 350V.
My advice is to buy some from your favorite reputable vendor and hope
for the best.

--Mike

--------------------------------------------------------------------
Mike Schway | [Picture your favorite quote here]
mschway@xxxxxxx |
--------------------------------------------------------------------
.

Relevant Pages

  • Re: Bartolomeo Aloia BA211
    ... follower has a larger current-sense resistance for the current source, ... then that load is TOO LOW. ... bottom tube to give Vgk applied to top tube which is nearly equal to ... 60mAdc, and phones of 32 ohms were connected to top cathode, then one ...
    (rec.audio.tubes)
  • Re: Amp output Z
    ... >>>In the real amp it must be something other a pure resistance of 10 ohms ... > voltage because the amp is unstable with no load. ... He believes that the output Z is about 10 ohms ... I think the 10 ohms output resistance is a guesstimate too. ...
    (sci.electronics.design)
  • Re: valve amp -> speaker impedance mismatch
    ... This is a greater resistance (not ... The higher the ohms of the load, the less current change in the load you ... The more bricks, the harder the truck works, but with an amp, the more load ...
    (rec.audio.tubes)
  • Re: Limited Bandwidth
    ... I built a typical phono amp with 3 12AX7s, ... My problem is that when I use any of my tube amps, ... So the 100k attenuator after the CF won't cause a problem because of its ... attenuator and the attenuator resistance. ...
    (rec.audio.tubes)
  • Re: how to control LED array? (follow-up)
    ... Fields also advise to take these 56 ohms base resistors? ... >> They will consume more current than the LEDs. ... The current sink is: ... pin of your micro (it's not uncommon to find output resistance slopes ...
    (sci.electronics.basics)