Re: Need help with an ASUS K8S-LA in a Compaq SR1365CL
- From: Paul <nospam@xxxxxxxxxx>
- Date: Mon, 30 Apr 2007 15:52:04 -0400
Peter Bogiatzidis wrote:
Paul,
Thanks for your response.
I checked the BIOS chip and unfortunately it is soldered in place. I also tried resetting CMOS. Afterwards, I was still unable to install Windows XP Home on the original SATA drive.
As you suggested, I was able to run Knoppix Live 3.4 from CD and could access the Internet as well as print to a network printer. One thing that I noticed was that the SATA was not recognized, or, perhaps better stated, that it couldn't be mounted in Knoppix. I'm not very fluent in Knoppix (aka Linux?), so I may be missing some key points here.
What does all of this mean? Does the fact that the PC will boot Knoppix from CD and work mean that both the motherboard and the BIOS chip are okay?
I should also mention that prior to my original post I found that there are 6 potential channel devices that appear in BIOS. The first and second channels allow for 2 IDE devices each, while the third and fourth only allow one SATA device each. I learned this by trial and error while trying different type drives (IDE & SATA) and connecting them to the various IDE or SATA connections on the motherboard.
Currently, there are no first channel devices shown, as there are no IDE hard drives connected. The second channel devices show up as the two CD/DVD drives that have always been connected to the system. The third channel device shows just the one SATA drive. If I switch the cable to the second SATA connector on the motherboard the drive will appear as the only device on the fourth channel.
With that, I'm still at a loss at understanding why the PC won't work or let me install Windows XP Home again. If it helps, I believe that the BIOS is dated 10/29/04 and reads as SIS 760-6A7I7A09-00.
As I said, thank you for your response. So far, booting Knoppix, accessing the Internet, and being able to print are the most productive things that I've been able to make this PC do since I began working on it. If you have any other ideas as to what is going on here, your help would be greatly appreciated.
Peter.
For native SATA support, it might help to use WinXP SP1 or later. If your
Windows XP Home disk is the original version, you can use a program like
AutoStreamer, to incorporate WinXP + SP1 and burn a new install CD.
The SIS964 Southbridge has been around for a while. Some motherboards
have a BIOS setting, allowing the SATA ports to be either set to
"native" mode or to "RAID" mode. Older boards might only support RAID,
and that could be an immature BIOS issue. Or, it may be possible there
are several revisions of 964, but that would be unfortunate if there were
true. I don't really know the history of the 964, except that it has been
around longer than a lot of other Southbridge chips.
The "native" mode *should* be supported by the native driver in WinXP SP1
or later. The "RAID" mode would require pressing F6 early in the install,
presenting a floppy with the driver, and giving windows a RAID driver.
You can get drivers from the download page of www.sis.com . For example,
this is the RAID driver. This is an 11MB download. To build a floppy,
you unzip the file, then find the "floppyimage" folder, and copy the contents
of "964_180" to your floppy. You should have a "txtsetup.oem" at the top
level of the floppy, plus the RAID folder and the SISRAID file. When you
press F6 during the install, the Windows installer should open the
floppy, read the txtsetup.oem, and if the enumeration of the chipset
matches the drivers, it will use the drivers as requested.
http://driver.sis.com/raid/raid411a.zip
If you are still having problems, another problem is apparently some
SATA drives that operate at 3Gbit/sec cable interface, have an
autonegotiation feature. Jumpering the drive to run at 1.5Gbit/sec
is sometimes needed, so the chipset can see the drive. And this is
because the chipset doesn't like the antics of the drive, during
startup. Forcing the disk drive to run at 1.5Gbit/sec, by using a
jumper, stops the autonegotiation function.
You can try downloading the SATA drive testing utility from the
hard drive maker's web site. Usually, such a utility boots from a
floppy, and allows testing of the drive. In the past, such utilities
have been picky about what silicon controls the hardware, so the
most likely thing to work, would be if the 964 was in "native" mode
in the BIOS. But that is another thing to try, if you want to
prove there is a working hardware interface.
So you still have some more testing to do, to prove or disprove
the "busted hardware" theory.
Note that the latest versions of Knoppix or Ubuntu Live CDs have
an install option. That would be another way to test whether software
is capable of using your hardware as it stands. You can always
blow away the Linux install, once you've proved it works, and install
WinXP over top.
So you have plenty of toys to play with :-)
Paul
.
- References:
- Need help with an ASUS K8S-LA in a Compaq SR1365CL
- From: Peter Bogiatzidis
- Re: Need help with an ASUS K8S-LA in a Compaq SR1365CL
- From: Paul
- Re: Need help with an ASUS K8S-LA in a Compaq SR1365CL
- From: Peter Bogiatzidis
- Need help with an ASUS K8S-LA in a Compaq SR1365CL
- Prev by Date: Re: Random Blank Screens...Black
- Previous by thread: Re: Need help with an ASUS K8S-LA in a Compaq SR1365CL
- Next by thread: System clock running fast on A7N8X deluxe?
- Index(es):
Relevant Pages
|
