Re: Bizarre hardware problem- Dell Dimension 8200

I suggest the following just to make sure everything is kosher on that HD,
before ripping everything apart.

1) Visit http://www.bootitng.com and download BootIt NG. Unzip the file and
execute BOOTITNG.EXE to create the bootable floppy/CD (accept the defaults).
Now reboot to the floppy/CD.

2) When the Welcome to Setup screen appears, select Cancel, follow the
prompts, and you will be taken to the BootIt NG desktop, where you can
select the Partition Manager.

3) Your HD will be displayed by default (HD0). Hit View MBR, and in the
dialog you will notice four entries in the MBR (Master Boot Record). Each
entry w/ a non-zero address represents one of your partitions. Make sure
the bootable partition (usually the first MBR entry) is marked Active. If
no, hit "Set Active", and the partition will indicate Active status. Now
hit "Std MBR", this will (re)initialize the boot loader in the MBR.
Finally, hit Apply to save the changes.

4) Hit Close, remove the BootIt NG floppy/CD, and hit Reboot.

Jim


"James N." <no@xxxxxxx> wrote in message
news:jdydneEqw7Rc1-benZ2dnUVZ_tSdnZ2d@xxxxxxxxxxxxxx
> Hi Guys,
>
> I seem to be having a bizarre hardware problem with one of my Dell
Dimension
> 8200 systems. First let me say that I have been working on computers for
> years, I do it for a living, and have personally never seen a problem
> exactly like this before.
>
> The system was working fine yesterday until I decided to do a system
> restart. I went through the normal process, the machine shutdown then
> brought up the Dell splash screen, but instead of re-starting windows XP
all
> I got was a blinking cursor in the very top left hand corner of the
screen.
> I did a hard reset on the machine but that didn't do anything to resolve
the
> problem.
>
> My first thought was that I either have a bad hard drive or a bad hard
drive
> controller on the motherboard. This is where the problem gets complicated.
>
> I went ahead and removed the hard drive and installed it in my other
> Dimension 8200 system. The drive works fine. It boots up properly without
> any issues and I'm able to get to the windows log in screen. The drive
> passes all manufacture diagnostics. (Seagate)
>
> Since the drive works fine in another system, I figured I must have a bad
> hard drive controller/motherboard. I got out a spare drive that I hard
> laying around and installed it in the malfunctioning system. Guess what,
the
> system boots up just fine with my spare drive.
>
> At this point, I've placed the original drive back in the malfunctioning
> computer and am still getting the blinking cursor. I can hear the drive
> spinning, so I know it's getting power. Another interesting note, I have
run
> the Dell Diagnostics CD and the hard drive test passes without any errors.
> One thing that is strange is that the hard drive makes an unusual
> buzzing/clicking noise when it's not being accessed, but when the tests
are
> running it sounds normal. I don't get any of these unusual noises when the
> drive is connected in my other system.
>
> I'm not exactly sure what the problem is, however I believe it is somehow
> related with the motherboard or integrated hard drive controller.
>
> Here are some of the things I've tried:
> 1. Tried new IDE cable.
> 2. Used external power source for HDD
> 3. Disconnected CD-ROM drives and used secondary IDE connector
> 4. Swapped video card just to rule it out
> 5. Removed all un-necessary PCI cards
> 6. Replaced bios battery and restored bios to defaults/verified all
settings
> 7. Reseated RAM modules
>
> Any hints would be appreciated at this point. Right now I'm at a loss and
> don't know of anything else I can do except to start replacing parts,
> starting with the motherboard.
>
> James
>
>


.

Relevant Pages

  • Re: Found one problem
    ... degree loft. ... However, I hit only two fairways, and one of those was a 3 wood where I ... I put 4 straight drives on the range to the ... closer to the ball. ...
    (rec.sport.golf)
  • Re: Phickelsons 4 wood
    ... and 9% of his drives are over 300. ... meaning he hit a perfect drive about 25-30 yards ... who actually hit 4W on 18? ... just Bones covering Phil's ass. ...
    (rec.sport.golf)
  • Re: 9 iron distance
    ... > Bruce Newman wrote: ... >>>there are NONE that can hit 280 yd drives consistently. ... it closer to 240 under cold, wet conditions. ...
    (rec.sport.golf)
  • Re: acer aspire one
    ... I'd suggest following that and ask if you hit any problems. ... I'm having a quick look at that, and I notice he's running the cmd thing on a Vista chamine, which has a several of bits and pieces wot XP doesn't for dealing with flash drives. ... He's also using a custom prepared XP install disk, wot has a few silly issues which whoever molished it CBA to fix. ...
    (uk.rec.sheds)
  • Re: Phickelsons 4 wood
    ... and 9% of his drives are over 300. ... who actually hit 4W on 18? ... citing someone who hit driver is not a great rebuttal. ... And if you say you would pull the latter, ...
    (rec.sport.golf)