Re: O2 Sensor problem
- From: "Jeff Strickland" <crwlr@xxxxxxxxx>
- Date: Thu, 31 Aug 2006 18:05:45 -0700
Also, the circuit operates on milivolts or some very low logic voltage like that. I don't really know or care, my point is, any problem with the connection points will translate into poor operation of the system.
This is one of those circuits that must perform to a certain level within a specific time frame, then do something different within another time frame, then report what it detects every so often -- a period of several times per second. The long and the short is that the signal is actually very complicated, and a poor connection will make the signal shape -- time and level -- be incorrect for what the computer is looking for. The result is that the signal is out of range, and the Check light will come on.
"Ray O" <rokigawaATtristarassociatesDOTcom> wrote in message news:aa91e$44f76857$44a4a10d$31230@xxxxxxxxxxxxxxxxxxxxxxxxxxxx
<davejohansen@xxxxxxxxx> wrote in message news:1157054292.940815.315500@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxThis is probably a dumb question, but how do I check if there's a
problem with the connection between the ECU and the O2 sensor?
Thanks,
Dave
It is not a dumb question. The way to check for a problem in the circuit between the ECU and O2 sensor is to check for continuity, basically zero resistance, between the O2 sensor and the corresponding pin on the ECU connector. It helps to have about a 5 or 6 foot long piece of wire to extend the reach of your ohm meter.
While you are checking, make sure the wire that leads into the pin on the ECU connector is not loose, and make sure the splice connection you made at the O2 sensor is good. In fact, I'd start by checking continuity in the wire before and after your splice.
Also, with the ignition off, you want to check for continuity between the O2 sensor circuit wires and ground. I doubt if this is a problem unless the vehicle was in an accident or heavily modified where wire harnesses were disturbed.
--
Ray O
(correct punctuation to reply)
Ray O wrote:<davejohansen@xxxxxxxxx> wrote in message
news:1156902858.195011.174310@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
> The check engine light came on in my 97 Geo Prizm (almost identical to
> a 97 Toyota Corolla). The code was P0141 (O2 Heater Circuit (Bank 1,
> Sensor 2)) and the Chilton manual said that
> that was the post-convertor O2 sensor. It had a little diagnostic test
> I could try and so I tried that out and according to the test it was
> bad. I replaced the sensor on Saturday, but then today on the way to
> work the check engine light came on. It was the exact same code. Does
> anyone have any suggestions on what the problem might be?
> Thanks,
> Dave
>
If you used an aftermarket O2 sensor, the problem may be with the sensor,
especially if you had to snip and join wires.
I would do the same check on the replacement sensor to see if it checks good
or bad. Keep in mind that you are checking the heater circuit and not the
O2 sensor operation. If the O2 sensor heater check out OK, check the heater
circuit wires back to the ECU for an open or short.
--
Ray O
(correct punctuation to reply)
.
- Follow-Ups:
- Re: O2 Sensor problem
- From: Coyoteboy
- Re: O2 Sensor problem
- References:
- Re: O2 Sensor problem
- From: Ray O
- Re: O2 Sensor problem
- Prev by Date: Re: OT - Coward Bush leaving Iraq to next administration
- Next by Date: Re: OT - Coward Bush leaving Iraq to next administration
- Previous by thread: Re: O2 Sensor problem
- Next by thread: Re: O2 Sensor problem
- Index(es):
Relevant Pages
|
